|
midrange.com
Only Server and QNNINSTS try to start.
No program document
No fault recovery script
The two DMP commands mentioned do not exist on any of our systems
The new system is not in production yet, so I'm planning on calling IBM
next week -- I'll update this when I have a resolution.
Bob
Chris Whisonant
<Chris.Whisonant@
comporium.com> To
Sent by: Lotus Domino on the iSeries / AS400
domino400-bounces <domino400@xxxxxxxxxxxx>
+rlaing=gemko.com cc
@midrange.com
Subject
Re: moving to new iSeries
09/30/2005 04:17
PM
Please respond to
Lotus Domino on
the iSeries /
AS400
<domino400@midran
ge.com>
Do any tasks other than SERVER and QNNINSTS start?
I can think of two initial possiblities
1 - Do you have a Program Document in your NAB that may be referring to a
file that may not exist on the new box?
2 - Do you have a script specified in the Fault Recovery section on your
server document? Does this script exist on the new box?
Also, do you have the DMPCLLSTK and/or DMPSVRSTKS commands? You can use
these while the jobs are starting up to generate a more detailed dump of
what they are doing and get that information to Lotus.
Chris Whisonant
Comporium
Senior Mid-Range Systems Administrator
IBM eServer Certified Systems Expert - iSeries Technical Solutions V5R2
IBM Certified System Administrator - Lotus Notes and Domino 6/6.5
803.326.7270 | 803.326.6142 fax
http://cwhisonant.blogspot.com/
domino400-bounces+chris.whisonant=comporium.com@xxxxxxxxxxxx wrote on
09/30/2005 03:58:46 PM:
> We're moving from an 800 to a 520 and did a full save on the 800 and
> restore on the 520. Updated the resource names and IP settings,
> disconnected the old box from the network and fired up one of our Domino
> servers on the new box. Server does not start, joblog messages follow.
> Tried firing up our Sametime and Quickplace servers on the new box and
they
> start OK. Take a look at the joblog messages and let me know if anyone
has
> any ideas
>
> There are two joblogs that appear after trying to start the server, one
for
> the SERVER job, the other for the QNNINSTS job. The messages below are
> from the SERVER job. There does't appear to anything meaningful in the
> QNNINSTS joblog.
>
> Both boxes V5R3, same PTF levels. Domino at 6.5.4 FP1 on both boxes
>
> MCH3402 Escape 40 09/30/05 15:43:56.562456
LIBNOTES
> QDOMINO654 *STMT LIBNOTES QDOMINO654 *STMT
> >From module . . . . . . . . : CLEANUP
> >From procedure . . . . . . : OSFaultRecoveryRemovePid
> Statement . . . . . . . . . : 1
> To module . . . . . . . . . : CLEANUP
> To procedure . . . . . . . : OSFaultRecoveryRemovePid
> Statement . . . . . . . . . : 1
> Message . . . . : Tried to refer to all or part of an object that no
> longer exists.
> Cause . . . . . : The most common cause is that a stored address to an
> object is no longer correct because that object was deleted or part of
the
> object was deleted
>
> CEE9901 Escape 30 09/30/05 15:43:56.604296 QLEAWI
> QSYS *STMT QP0ZPCPN QSYS *STMT
> >From module . . . . . . . . : QLEDEH
> >From procedure . . . . . . : Q LE leDefaultEh
> Statement . . . . . . . . . : 168
> To module . . . . . . . . . : QP0ZPCPN
> To procedure . . . . . . . : InvokeTargetPgm__FP11qp0z_pcp_cb
> Statement . . . . . . . . . : 187
> Message . . . . : Application error. MCH3402 unmonitored by LIBNOTES
at
> statement 0000000001, instruction X'0000'.
> Cause . . . . . : The application ended abnormally because an
exception
> occurred and was not handled. The name of the program to which the
> unhandled exception is sent is LIBNOTES CLEANUP
OSFaultRecoveryRemovePid.
> The program was stopped at the high-level language statement number(s)
> 0000000001 at the time the message was sent. If more than one statement
> number is shown, the program is an optimized ILE program. Optimization
> does not allow a single statement number to be determined. If *N is
shown
> as a value, it means the real value was not available.
> Recovery . . . : See the low level messages previously listed to
locate
> the cause of the exception. Correct any errors, and then try the
request
> again.
>
> Bob
>
>
> _______________________________________________
> This is the Lotus Domino on the iSeries / AS400 (Domino400) mailing list
> To post a message email: Domino400@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/domino400
> or email: Domino400-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/domino400.
>
_______________________________________________
This is the Lotus Domino on the iSeries / AS400 (Domino400) mailing list
To post a message email: Domino400@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/domino400
or email: Domino400-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/domino400.
As an Amazon Associate we earn from qualifying purchases.
This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].
Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.
