Help Setup Dial In PPP

["Roger Vicker, CCP" <rvicker@xxxxxxxxxx>]

HELP, I've pulled my hair out over this (:-| and worn the
softcopy/infocenter cd to a blob of plastic.

I am trying to setup a dial in to an AS/400. The modems connect and
the PC indicates it is verifying user and password but then
disconnects. The message usually says:
>
> The computer you're dialing in to cannot establish
>  a Dial-Up Networking connection.
> Check your password, and then try again.

and QSYSOPR get a "User xxxx not found." 
Msgid=TCP83AB

If I try a user name that is in the validation list as CHAP only the
messages is:
> Dial-Up Networking could not negotiate a compatible set
> of network protocols you specified in the Server Type settings.
> Check your network configuration in the Control Panel
> then try the connection again.

and no message in QSYSOPR.

The printer output for the profile job shows:
0:22:33.522 === Incoming call received.
0:22:33.526 === Establishing point-to-point connection for profile
DIAL_IN01.
0:22:36.330 === NOTE: REJECTED LCP OPTION 0D (lcp_rcvreqci)
0:22:40.230 === WARNING: OS/400 REJECTS PEER ADDRESS '0.0.0.0'. (NO
ALTERNATE ADDRESS FOR PEER AVAILABLE
0:22:40.244 <== NOTE: NO SUPPORT IN OS/400 FOR PROTOCOL 80FD, STREAM
LCP
0:22:44.085 === Status code X'54001490' from device PPPINTCP.
0:22:44.912 === Status code X'54001490' from device PPPINTCP.
0:22:45.656 === WARNING: LINK DOWN] ERRNO ENETDOWN(3433)
0:22:45.659 === NOTE: LCP_ADMIN_CLOSE: REASON 9 CALL ENDED (LINE
DROPPED).
0:22:45.660 === WARNING: LCP: IGNORING unexpected RCVTERMREQ event in
INITIAL state.
0:22:48.427 === Message received for Point-to-Point Profile DIAL_IN01,
Reason Code 1.
0:22:48.557 === Attempting modem dial/answer.
0:22:48.558 ==> ATS0=1
0:22:49.087 <== OK
0:22:49.088 === Waiting for incoming call.

or

0:30:29.383 === Incoming call received.
0:30:29.453 === Establishing point-to-point connection for profile
DIAL_IN01.
0:30:32.188 === NOTE: REJECTED LCP OPTION 0D (lcp_rcvreqci)
0:30:34.418 === NOTE: CHAP VERIFY failed. *VLDL PPPIN01    ENTRY NOT
FOUND. (rc 10)
0:30:34.433 === NOTE: LCP_ADMIN_CLOSE: REASON 2 AS/400 WAS UNABLE TO
AUTHENTICATE THE REMOTE PEER.
0:30:35.507 === Status code X'54001490' from device PPPINTCP.
0:30:36.320 === Status code X'54001490' from device PPPINTCP.
0:30:39.946 === Message received for Point-to-Point Profile DIAL_IN01,
Reason Code 1.
0:30:40.076 === Attempting modem dial/answer.
0:30:40.077 ==> ATS0=1
0:30:40.606 <== OK
0:30:40.711 === Waiting for incoming call.

The only way I've been able to get a connection is to remove the
REMOTE REQUIRED SYSTEM IDENTIFICATION. I don't want to run this way
without security to restrict who can get access to the line, I know
that the rest of the system depends on object/IFS security.

BTW. Is there a way to have the validation list automatically updated
to be the same as the AS/400 user profiles?
            Is there a way to have the connection profile
automatically started at IPL?

Thanks to all and to all a productive new year.

Roger Vicker, CCP

*******
SETUPS
*******

AS/400 is
    running DHCP 10.0.0.30 to 10.0.0.254 subnet 255.255.255.0
    but no DNS
    is on an ethernet lan (10.0.0.1 mask 255.255.255.0)
    @ V4R4M0

AS/400 Connections Profile Setup via OpsNav
General
               Type PPP
                Line Switched
TCP/IP
               Local IP    10.0.0.1   (same as the Ethernet card for
LAN)
                Remote    Dynamically Assign
                Routing    Allow IP Forward
                Routing    Request header compression (VJ)
Authentication
                Remote Require remote sys ID
                Remote Allow PAP
                Remote Validation list (has names as PAP only)
                Local  (not checked for enable local sys id)

PC Dial up @ Win98
Server types
                Type of server:
                    PPP: Internet, Windows NT Server, Windows 98
                Log on to network
                Enable software compression
                Require encrypted password
                TCP/IP
                    Server assigned IP
                    Server assigned name server addresses
                    use IP header compression
                    use default gateway on remote network


--
*** Vicker Programming and Service *** Have bits will byte ***
www.vicker.com ***
Fine day for a good workout. Steal something heavy.
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---