Re: AS/400 FRONT PANEL KEYS CONFIGURATION -- MIDRANGE-L

The access paths are being built file in recovery by these jobs:
QDBSRV04
QDBSRV05
I also notice that there are more of these jobs on the system but they are
not actively doing anything.  These are the list:
QDBSRVXR
QDBSRVXR2
QDBSRV01
QDBSRV02
QDBSRV03
Anyone with knowledge why some are active while the rest are dormant?

Thanks


----- Original Message -----
From: "oludare" <oludare@ix.netcom.com>
To: <MIDRANGE-L@midrange.com>
Sent: Monday, April 03, 2000 12:18 PM
Subject: Re: AS/400 FRONT PANEL KEYS CONFIGURATION


> Yes, I figured it out.  The problem was 'AUXILIARY STORAGE IS=0'.  I think
> there was a "PROGRAM DUMP" that used all DASD space.  Solution: I IPL
> manually and deleted all JOBLOGS, PROGRAM QUEs, JOBQs et al but OUTQs.  It
> resolved my problem but know I have to wait for some of my HUGE files
access
> path to be created before I let the users back on.  The access path jobs
(2)
> are taking over +++++ of PROCESSOR time.
>
> Thanks for your response.
>
> Dare
>
> ----- Original Message -----
> From: "Rob Berendt" <rob@dekko.com>
> To: <MIDRANGE-L@midrange.com>
> Sent: Monday, April 03, 2000 10:30 AM
> Subject: Re: AS/400 FRONT PANEL KEYS CONFIGURATION
>
>
> > | 1.5.1.8 IPL Overview, Primary Partition
> >
> >
> > | Figure 23 shows the system reference codes that are displayed on the
> > | control panel, and approximately how long they remain displayed while
> the
> > | IPL is progressing on the primary partition. If you notice a code
> > | displayed longer than it should or a code not listed, see Handling and
> > | Reporting System Problems.
> > ...
> >  |  C6XX 4XXX  Testing system configuration (1 - 10 minutes)
> > ...
> >
> >
> > This is what the 11-3 means.
> > If you start at 11 and press enter, 11 enter, 12 enter, and so
> > on.  The next ?10? numbers will help IBM determine diagnostics.
> > For example, if it was a disk problem then one of the other
> > problems will tell them which drive, and so on.
> >
> > If this is part of a normal IPL may I recommend upgrading to V4R4?
> > V4R4 will tell you, in words, what IPL step is going on.  It displays
> > this on the system console.  Takes away the fun of trying to browse
> > reference manuals to determine the codes as a method of passing the
> > time during an IPL.
> >
> >
> >
> >
> >
> > oludare@ix.netcom.com on 04/03/2000 09:10:18 AM
> > Please respond to MIDRANGE-L@midrange.com@Internet
> > To: MIDRANGE-L@midrange.com@Internet
> > cc:
> > Fax to:
> > Subject: Re: AS/400 FRONT PANEL KEYS CONFIGURATION
> >
> > I am on 9406-510, V3R7M0.  What does error code C6244205 and 11-3 mean?
> >
> > Thank you.
> >   ----- Original Message -----
> >   From: Seref ERTEKIN
> >   To: MIDRANGE-L@midrange.com
> >   Sent: Wednesday, March 22, 2000 8:32 AM
> >   Subject: Re: AS/400 FRONT PANEL KEYS CONFIGURATION
> >
> >
> >     1.1.2 IPL Types and Modes
> >
> >     The IPL types and modes are:
> >
> >     A M       Performs a Manual IPL from the A side of the disk.  This
> mode may be used when applying or
> >               removing Licensed Internal Code (LIC) PTFs.  It can also
be
> used to power off the system.
> >
> >               Use this type and mode only under the direction of your
> support representative.
> >
> >     A N       Performs a Normal IPL from the A side of the disk.
> >
> >               This mode should only be used when B N does not work and
you
> are told to do so by your support
> >               representative.
> >
> >     B M       Performs a Manual IPL from the B side of the disk.  This
> mode should only be used when an attended
> >               IPL must be performed or you need to power off the system.
> This type of IPL is used when you need to
> >               change the system date and time permanently.
> >
> >     B N       Performs a normal IPL from the B side of the disk.  This
is
> the type and mode used most of the time.  It
> >               is also the mode the system must be in if you want to do
an
> unattended IPL.
> >
> >     C M       Allows service representatives to perform a special IPL.
> This mode is for use only by service
> >               representatives.  Never IPL in this type and mode.
> >
> >     C N       Allows service representatives to perform a special IPL.
> This mode is for use only by service
> >               representatives.  Never IPL in this type and mode.
> >
> >     D M       Performs a manual IPL from either CD-ROM or tape.  This
mode
> is used to install Licensed Internal
> >               Code and the OS/400 operating system in attended mode.
This
> is the most often used IPL type and
> >               mode for installation.
> >
> >     D N       Performs a normal IPL from either CD-ROM or tape.  This
mode
> is used to install Licensed Internal Code
> >               and the OS/400 operating system in unattended mode.
> >
> >     Manual    When the mode is set to Manual (M), the system allows you
to
> do all manual IPLs, such as an
> >               operator-attended IPL from disk, CD-ROM or tape.  Manual
> mode also allows you to do some manual
> >               control functions, such as selecting an IPL type and mode
or
> displaying the kind of IPL that the system is
> >               set to run. However, in manual mode, you cannot do a
remote
> IPL, an IPL by date and time, or an IPL
> >               after a power failure.
> >
> >               Note:  You should set the mode to Manual only when it is
> necessary.  This ensures that no one
> >                      accidentally presses the Power pushbutton and
causes
> the system to stop.
> >
> >
> >     Normal    The Normal mode allows you to turn the power on and then
> automatically start the system in any of
> >               the following ways:
> >
> >                  IPL remotely
> >
> >                  IPL by date and time
> >
> >                  IPL after a power failure
> >
> >
> >               Note:  Your system should be in Normal mode most of the
> time.
> >
> >
> >     The table in Figure 1-3 in topic 1.1.2 summarizes what operations
you
> can do in the Manual (M) or Normal (N)
> >     IPL modes:
> >
> >     Note:  You can display the kind of IPL the system is set to do when
> the system is in any mode.
> >
> >
> >     If you want to stop the system when the mode is set to Normal, use
the
> Power Down System (PWRDWNSYS)
> >     command at any display station after you stop the AS/400 Advanced 36
> machines.  You must have QSYSOPR
> >     authority to use the Power Down System (PWRDWNSYS) command.
> >     ----- Original Message -----
> >     From: oludare
> >     To: AS/400 Midrange Usergroup
> >     Cc: Mike Thomas
> >     Sent: Wednesday, March 22, 2000 12:04 AM
> >     Subject: AS/400 FRONT PANEL KEYS CONFIGURATION
> >
> >
> >     Hi guys,
> >
> >     what are the combination keys for AS/400 FRONT PANEL CONFIGURATION.
> >     I know that 01 B = Normal Unattended IPL Mode.  What are the others?
> >
> >     Thanks for your input.
> >
> >
> >     Dare
> >
> >
> >
> >
> >
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
david@midrange.com
> +---

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---