RE: 5494 cud setup

[Chris Bipes <chris.bipes@xxxxxxxxxxxxxxx>]

We are running a Perle box over our LAN.  The line is a standard Ethernet
line.  Here is the controller & devices.


CRTCTLAPPC CTLD(PERLECTL) LINKTYPE(*ANYNW) ONLINE(*YES) APPN(*YES) +
         RMTNETID(*NETATR) RMTCPNAME(TCPIP1) NODETYPE(*LENNODE) +
         HPR(*YES) HPRPTHSWT(*NO) BEXROLE(*NETNODE) TMSGRPNBR(1) +
         AUTOCRTDEV(*ALL) AUTODLTDEV(1440) USRDFN1(*LIND) +
         USRDFN2(*LIND) USRDFN3(*LIND) CMNRCYLMT(2 5) +
         MSGQ(*SYSVAL) +
         TEXT('PERLE CONTROLLER, Anynet Control Point "TCPIP1"')

CRTDEVAPPC DEVD(RMT02) LOCADR(00) RMTLOCNAME(RMT02) ONLINE(*NO) +
         LCLLOCNAME(systema1) RMTNETID(*NETATR) CTL(PERLECTL) +
         MODE(*NETATR) MSGQ(*CTLD) APPN(*YES) SNGSSN(*NO) +
         TEXT('AUTOMATICALLY CREATED BY SYSTEM')

CRTDEVAPPC DEVD(RMT04) LOCADR(00) RMTLOCNAME(RMT04) ONLINE(*NO) +
         LCLLOCNAME(systema1) RMTNETID(*NETATR) CTL(PERLECTL) +
         MODE(*NETATR) MSGQ(*CTLD) APPN(*YES) SNGSSN(*NO) +
         TEXT('AUTOMATICALLY CREATED BY SYSTEM')

CRTDEVAPPC DEVD(RMT05) LOCADR(00) RMTLOCNAME(RMT05) ONLINE(*NO) +
         LCLLOCNAME(systema1) RMTNETID(*NETATR) CTL(PERLECTL) +
         MODE(*NETATR) MSGQ(*CTLD) APPN(*YES) SNGSSN(*NO) +
         TEXT('AUTOMATICALLY CREATED BY SYSTEM')

CRTDEVAPPC DEVD(RMT06) LOCADR(00) RMTLOCNAME(RMT06) ONLINE(*NO) +
         LCLLOCNAME(systema1) RMTNETID(*NETATR) CTL(PERLECTL) +
         MODE(*NETATR) MSGQ(*CTLD) APPN(*YES) SNGSSN(*NO) +
         TEXT('AUTOMATICALLY CREATED BY SYSTEM')


HTH

Christopher K. Bipes    mailto:ChrisB@Cross-Check.com
Sr. Programmer/Analyst  mailto:Chris_Bipes@Yahoo.com
CrossCheck, Inc.        http://www.cross-check.com
6119 State Farm Drive   Phone: 707 586-0551 x 1102
Rohnert Park CA  94928  Fax: 707 586-1884

If consistency is the hobgoblin of little minds, only geniuses work here.
Karen Herbelin - Readers Digest 3/2000

-----Original Message-----
From: ddetz@zinccorp.com [mailto:ddetz@zinccorp.com]
Sent: Friday, August 18, 2000 4:39 AM
To: MIDRANGE-L@midrange.com
Subject: FW: 5494 cud setup


I'm in the process of shutting down two AS/400's and replacing w/ 5494's
running on a 620 v4.4.  Can someone help in the line/ctl/dev set up.  I
can't remember how different it was from the 5294/5394 days (I do have those
set up now).  But I need help on line type, exange id...ect.  been a long
time.... If you have examples those would be appreciated.... TIA


Dawn L. Detz
System Administrator
Zinc Corporation of America
300 Frankfort Road
Monaca, PA  15061-2295
ddetz@zinccorp.com
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---