Re: V5R3 serious problem

[Al Barsa <barsa@xxxxxxxxxxxxxxxxxxx>]

You should not have had a problem.  There's no (easy) telling what the
cause was, but I always check for damage B4 I do a new release, and this
generally insures that it will be OK..  We had damage loading onto the 520,
but not the 270 prior.  There are two versions of V5R3 (GA1 and GA2 [I hate
when they do that they should just admit that it wasn't ready and either
not release it, or release it as V5R3M0 and V5R3M1, but they are too
cheap.])  Be sure to determine that you are using GA2.  (They did the same
bull@#$% fir V5R2 also.

Al

Al Barsa, Jr.
Barsa Consulting Group, LLC

400>390

"i" comes before "p", "x" and "z"
e gads

Our system's had more names than Elizabeth Taylor!

914-251-1234
914-251-9406 fax

http://www.barsaconsulting.com
http://www.taatool.com
http://www.as400connection.com



                                                                           
             Thomas Hauber                                                 
             <thauber@printgrc                                             
             .com>                                                      To 
             Sent by:                  Midrange Systems Technical          
             midrange-l-bounce         Discussion                          
             s@xxxxxxxxxxxx            <midrange-l@xxxxxxxxxxxx>           
                                                                        cc 
                                                                           
             12/07/2004 10:24                                      Subject 
             AM                        Re: V5R3 serious problem            
                                                                           
                                                                           
             Please respond to                                             
             Midrange Systems                                              
                 Technical                                                 
                Discussion                                                 
             <midrange-l@midra                                             
                 nge.com>                                                  
                                                                           
                                                                           




820

Thomas Hauber
Senior Programmer/Analyst
General Ribbon Corp.



Al Barsa wrote:

>What hardware are you running on?  7xx, 8xx or 5xx?
>
>It makes a difference.
>
>Al
>
>Al Barsa, Jr.
>Barsa Consulting Group, LLC
>
>400>390
>
>"i" comes before "p", "x" and "z"
>e gads
>
>Our system's had more names than Elizabeth Taylor!
>
>914-251-1234
>914-251-9406 fax
>
>http://www.barsaconsulting.com
>http://www.taatool.com
>http://www.as400connection.com
>
>
>
>

>             "Eduard van den

>             Braken"

>             <Eduard.van.den.B                                          To

>             raken@interaccess         "Midrange Systems Technical

>             .nl>                      Discussion"

>             Sent by:                  <midrange-l@xxxxxxxxxxxx>

>             midrange-l-bounce                                          cc

>             s@xxxxxxxxxxxx

>                                                                   Subject

>                                       RE: V5R3 serious problem

>             12/07/2004 02:55

>             AM

>

>

>             Please respond to

>             Midrange Systems

>                 Technical

>                Discussion

>             <midrange-l@midra

>                 nge.com>

>

>

>
>
>
>
>Did you install the PTF's ??
>
>-----Original Message-----
>From: midrange-l-bounces@xxxxxxxxxxxx
>[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Thomas Hauber
>Sent: maandag 6 december 2004 16:50
>To: Midrange Systems Technical Discussion
>Subject: V5R3 serious problem
>
>We upgraded this weekend to 5.3 and the install went fine.  Where I
>started to notices problems was when the Go Save 21 failed due to a
>damaged TAP01 object.  I ran a Rclstg and then a full system save.  All
>was fine on Sunday.  This morning I have jobs that will enter the jobq,
>process correctly and go into an EOJ status.  But they never end!
>
>Has anyone seen this?
>
>--
>Thomas Hauber
>Senior Programmer/Analyst
>General Ribbon Corp.
>
>--
>This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
>list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
>unsubscribe, or change list options,
>visit: http://lists.midrange.com/mailman/listinfo/midrange-l
>or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
>moment to review the archives at http://archive.midrange.com/midrange-l.
>
>
>--
>This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
>To post a message email: MIDRANGE-L@xxxxxxxxxxxx
>To subscribe, unsubscribe, or change list options,
>visit: http://lists.midrange.com/mailman/listinfo/midrange-l
>or email: MIDRANGE-L-request@xxxxxxxxxxxx
>Before posting, please take a moment to review the archives
>at http://archive.midrange.com/midrange-l.
>
>
>
>--
>This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
>To post a message email: MIDRANGE-L@xxxxxxxxxxxx
>To subscribe, unsubscribe, or change list options,
>visit: http://lists.midrange.com/mailman/listinfo/midrange-l
>or email: MIDRANGE-L-request@xxxxxxxxxxxx
>Before posting, please take a moment to review the archives
>at http://archive.midrange.com/midrange-l.
>
>
>

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.