RE: System i5 first boot -- MIDRANGE-L

Hi Brian,

Thanks for the detailed response.  I followed your instructions but was only
able to go up to 64 (no 65).  Is there something missing from the below
instructions?


Thanks,
Aaron Bartell 

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Brian
Sent: Monday, November 13, 2006 4:08 PM
To: Midrange Systems Technical Discussion
Subject: Re: System i5 first boot

Aaron,

It looks like your system was configured for LAN console. You should have
followed the instructions in STEP 7 "Cable the system unit and Operations
Console (LAN)" of the "Quick start guide for i5 520" that you referenced. If
you follow the instructions there it will tell you how the IP address for
the LAN console is established. You can connect the console PC to the T5
port of the i5 either through a straight ethernet cable (not crossover) or
via a hub or switch; I've done it both ways. I set one of these up two weeks
ago and it was a piece of cake if you RTFM and follow the directions.

To see what console your system thinks it has do the following from the
front panel of the i5:

press the up arrow once to change the 01 to a 02 then press enter.
press enter again to accept the B<.
press the down arrow once to change the N< to a M< and then press enter.
press enter to accept the T<.
You're now in manual mode.
press the up arrow untill you reach 25 and press enter, it should respond
with 25 00.
press the up arrow once more to reach 26 and press enter, it should respond
with 26 00. If it responds with 26 FF, repeat the 25, 26 combination again.
press the up arrow untill you reach 65 and press enter.
press the down arrow untill you reach 21 and press enter.
press the down arrow untill you reach 11 and press enter.
You should see A603500A displayed. If you do, this means your set for LAN
console.

Kind regards,

BJ




On 11/13/06, albartell <albartell@xxxxxxxxx> wrote:

First, look to see how you're supposed to be connected.  Your system 
is

configured to use something, probably Op's Console.

Where do I look to see how my system is configured?  On the packing 
list that shipped with my system I have this line item on it:

Feature   Quantity
5553         001        Sys console-ethernet no IOP

You really need to RTFM.


I followed the "Quick start guide for i5 520" that came with my 
machine - didn't get me there.  All the other links that I have 
followed have not gotten me there (i.e. IBM Systems Hardware 
Information Center which was somehow installed on my desktop and I 
have been pouring through that).  I should not need to be well versed 
as an iSeries admin to get my machine booted for the first time.

Can somebody confirm that I should be able to configure my iSeries if 
I connect a desktop PC to it via ethernet cable that has the wires 
switched for peer-to-peer capabilities (i.e. the desktop is directly 
etherneted into the iSeries without any other devices in-between)

On a last note, the display panel on my latest boot is displaying "01    B
N  V=F"  with a single "T" on the second line.

Thanks for any direction you can provide, Aaron Bartell

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of rob@xxxxxxxxx
Sent: Monday, November 13, 2006 10:50 AM
To: Midrange Systems Technical Discussion
Subject: RE: System i5 first boot

First, look to see how you're supposed to be connected.  Your system 
is configured to use something, probably Op's Console.  You really 
need to RTFM.

Even if you do buy:  twinax card (providing you have a slot for it), 
twinax terminal, twinax cabling, etc, just shoving all this in doesn't 
automatically make this your system console.

And twinax is not the magic bullet some altzeimers seem to think it is.
I've had a lot of issues with it in the past.  Twinax cards going bad. 
Bad twinax cabling, address conflicts, baluns screwed up, terminals 
going bad, electrical shock from the attaching the cable because the 
wall plug was reversed, repeaters all needing to be replaced because 
5250 signal is not as strong in an iSeries as it was in an AS/400, and 
more.

Op's console was problem free for me.
HMC, (now that most of the early ship issues have been worked out) is 
quite reliable now.

Plus, with the newer technologies you can get remote access much easier.

Rob Berendt
--
Group Dekko Services, LLC
Dept 01.073
PO Box 2000
Dock 108
6928N 400E
Kendallville, IN 46755
http://www.dekko.com





"albartell" <albartell@xxxxxxxxx>
Sent by: midrange-l-bounces@xxxxxxxxxxxx
11/13/2006 11:24 AM
Please respond to
Midrange Systems Technical Discussion <midrange-l@xxxxxxxxxxxx>


To
"'Midrange Systems Technical Discussion'" <midrange-l@xxxxxxxxxxxx> cc

Subject
RE: System i5 first boot






Hmmm... I get the feeling that is the direction I should be going also.

It has been quite some time since I have been an operator (when I 
actually used a dumb terminal). Is this what I should be looking at

getting?


http://cgi.ebay.com/IBM-3476-amber-and-greens-3476_W0QQitemZ1200426295
89QQih

Z002QQcategoryZ162QQrdZ1QQssPageNameZWD1VQQcmdZViewItem

Looks like it is going to run me about $145.  Those things must be 
gaining speed as collectors items!  I seem to remember a plethora of 
them at my previous employer that were all going the way of the buffalo.

Aaron Bartell

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Joe Pluta
Sent: Monday, November 13, 2006 10:12 AM
To: 'Midrange Systems Technical Discussion'
Subject: RE: System i5 first boot

I don't use the HMC, Aaron, I use a $50 dumb tube and a twinax brick. 
I've never had any problems.

Joe

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, 
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take 
a moment to review the archives at 
http://archive.midrange.com/midrange-l.


--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, 
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take 
a moment to review the archives at 
http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing 
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, 
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take 
a moment to review the archives at 
http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe,
or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.