RE: Link Loader Failure and B600 0901 after v5r2 cume install

["David C. Shea" <dshea@xxxxxxxxxxxx>]

Pete:

Great to hear from you.

That makes sense.  I tried installing AC3, but it thought it was already installed.  I just removed AC3, DCM and DG1 and will reinstall later today or tonight.

I had a thought, though...

If I reinstall these from the original CDs, I'm guessing I'd have to install all the cume and groups, which sort of got me into this mess in the first place.  Should I reinstall these things from my full system save tape instead?

DAVE

****************************************************
Go...FASTER!  Without an Upgrade!
ARCTOOLS/400(tm) and ReorgWizard(tm)
www.arctools.com
DCSoftware,Inc.
Ph:  508.435.8243 x200
Fax:508.435.4498
Current versions: ARCTOOLS v7.1.1, ReorgWizard v3.1.5, JDE Module v3, BPCS Module v1
*****************************************************


-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Pete Massiello
Sent: Thursday, September 13, 2007 4:28 AM
To: 'Midrange Systems Technical Discussion'
Subject: RE: Link Loader Failure and B600 0901 after v5r2 cume install

Dave,

	When you have AC3 installed on a system that you are doing a restore
on, you actually have to reinstall AC3 from the PID CDs in order for the
product to properly resynchronize.  I have seen this required to be done if
you are using BRMS or not in your Save/Restore strategy.

	Pete

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of David C. Shea
Sent: Wednesday, September 12, 2007 10:09 PM
To: Midrange Systems Technical Discussion
Subject: RE: Link Loader Failure and B600 0901 after v5r2 cume install

Rob:
Thanks for the OPT02 fix.  Well done!

Re STRTCPSVR - not from the command line, from Navigator.  No dice.  I tried
from the command line, too.  No dice.

I'll try reinstalling AC3.

Argh.  This scratch recovery _almost_ worked.

Looking at the history log, I'm seeing complaints that SSL Telnet can't
start because either ac3 or DCM or DG1 are not installed.  I'll uninstall
and reinstall all three.

Bummer.

****************************************************
Go...FASTER!  Without an Upgrade!
ARCTOOLS/400(tm) and ReorgWizard(tm)
www.arctools.com
DCSoftware,Inc.
Ph:  508.435.8243 x200
Fax:508.435.4498
Current versions: ARCTOOLS v7.1.1, ReorgWizard v3.1.5, JDE Module v3, BPCS
Module v1
*****************************************************


-----Original Message-----
From: midrange-l-bounces+dshea=arctools.com@xxxxxxxxxxxx
[mailto:midrange-l-bounces+dshea=arctools.com@xxxxxxxxxxxx] On Behalf Of
rob@xxxxxxxxx
Sent: Wednesday, September 12, 2007 7:46 PM
To: Midrange Systems Technical Discussion
Subject: RE: Link Loader Failure and B600 0901 after v5r2 cume install

WRKCFGSTS *DEV *OPT
Vary them off
1 - STRSST
1. Start a service tool
7. Hardware service manager
3.  Locate resource by resource name
OPT01
3.  Locate resource by resource name*htt
OPT02
Verify both exist (sort of)
3.  Locate resource by resource name
OPT01
4=Remove
3.  Locate resource by resource name
OPT02
2=Change detail
Rename it to OPT01
F3 like hell
WRKDEVD *OPT
Fix those

2 - Have you performed a STRTCPSVR SERVER(*HTTP) HTTPSVR(ADMIN)

Rob Berendt