RE: Custom DQSIGNON

["Laine, Rogers" <rlaine@xxxxxxxxxxxxxxx>]

I know for sure that I'm using the correct one, that QDSIGNON for the 10 character password.

 

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of DeLong, Eric
Sent: Wednesday, September 09, 2009 4:28 PM
To: Midrange Systems Technical Discussion
Subject: RE: Custom DQSIGNON

Depending on your security configuration, you might need to pattern that off QDSIGNON2 (I think).  The difference has to do with the length of the password field, as well as allowing lower case characters.

-Eric DeLong

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Laine, Rogers
Sent: Wednesday, September 09, 2009 4:21 PM
To: Midrange Systems Technical Discussion
Subject: RE: Custom DQSIGNON

Lukas,

I failed to list that I did the CHGSBSD command and the ENDSBS and the STRSBS ones too.

This is the error I'm seeing the the log, that my be of help...

                          Additional Message Information                         
                                                                                
 Message ID . . . . . . :   CPF1164       Severity . . . . . . . :   00         
 Message type . . . . . :   Completion                                          
 Date sent  . . . . . . :   09/09/09      Time sent  . . . . . . :   16:13:57   
                                                                                
 Message . . . . :   Job 007525/MISRML9/QPADEV000L ended on 09/09/09 at         
   16:13:57; .012 seconds used; end code 30                                     
                                                                                
                     X.                                                         
 Cause . . . . . :   Job 007525/MISRML9/QPADEV000L completed on 09/09/09 at     
   16:13:57 after it used .012 seconds processing unit time.  The job had       
   ending code 30. The job ended after 1 routing steps with a secondary ending  
   code of 0.  The job ending codes and their meanings are as follows:          
      0 - The job completed normally.                                           
     10 - The job completed normally during controlled ending or controlled     
   subsystem ending.                                                            
     20 - The job exceeded end severity (ENDSEV job attribute).                 
                                                                        More... 

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Lukas Beeler
Sent: Wednesday, September 09, 2009 4:01 PM
To: Midrange Systems Technical Discussion
Subject: Re: Custom DQSIGNON

On Wed, Sep 9, 2009 at 22:55, Laine, Rogers<rlaine@xxxxxxxxxxxxxxx> wrote:
> 4. I go to change my test user profile to use MYSIGNON.
>
>    CHGUSRPRF USRPRF(MISRML9) INLPGM(QGPL/MYSIGNON)

The Sign-On screen is part of the subsystem describtion, and has nothing to do with the user profile. The sign on screen is displayed before the system knows which user sits there.

Use CHGSBSD with the SGNDSPF parameter to change it. Remember to restart the subsystem.

--
Read my blog at http://projectdream.org
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a moment to review the archives at http://archive.midrange.com/midrange-l.

************************************************
This E-Mail transmission (and/or the documents accompanying it) may contain information belonging to the sender which is confidential, privileged and/or exempt from disclosure under applicable law. The information is intended only for the use of the individual(s) or entity named above. If you are not the intended recipient, you are hereby notified that any disclosure, copying, distribution or the taking of any action in reliance on the contents of this information is strictly prohibited. If you have received this E-Mail transmission in error, please immediately notify us by return E-Mail or telephone to arrange for return of its contents including any documents.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a moment to review the archives at http://archive.midrange.com/midrange-l.