Re: CPF6DF2 error

[Michael Ryan <michaelrtr@xxxxxxxxx>]

Paper size correct? Output type is overlay?

On Thu, Dec 3, 2009 at 2:08 PM, Alan Shore <AlanShore@xxxxxxxx> wrote:

> Thanks for your reply Michael
> The overlay was from the AFP print driver, and landscape orientation was
> specified
>
>
>
> Alan Shore
> Programmer/Analyst, Direct Response
> E:AShore@xxxxxxxx
> P:(631) 200-5019
> C:(631) 880-8640
> "If you're going through Hell, keep going" - Winston Churchill
>
>
>
>             Michael Ryan
>             <michaelrtr@gmail
>             .com>                                                      To
>             Sent by:                  Midrange Systems Technical
>             midrange-l-bounce         Discussion
>             s@xxxxxxxxxxxx            <midrange-l@xxxxxxxxxxxx>
>                                                                        cc
>
>             12/03/2009 01:54                                      Subject
>             PM                        Re: CPF6DF2 error
>
>
>             Please respond to
>             Midrange Systems
>                 Technical
>                Discussion
>             <midrange-l@midra
>                 nge.com>
>
>
>
>
>
>
> How did you create the overlay? If from the AFP print driver, did you
> specify landscape orientation? Just a WAG.
>
> On Thu, Dec 3, 2009 at 1:44 PM, Alan Shore <AlanShore@xxxxxxxx> wrote:
>
> > Hi guys
> > unfortunately, it seems that nobody else has had this problem, but I have
> > persevered.
> > I started from scratch, changing my OVRPRTF command on the LPI,CPI   one
> > parameter at a time until I eventually arrived at the following
> > OVRPRTF    FILE(PICKLGL) DEVTYPE(*AFPDS) PAGESIZE(8.5 +
> >             14 *UOM) LPI(8) CPI(16.7) FRONTMGN(.7 +
> >             1.0) PAGRTT(90)  +
> >             OUTQ(RMTIBM) SAVE(*YES)
> > This produced data printed on legal size paper, landscape format that
> > looked close to where I want the data to print
> >
> > I then changed the above to include my overlay
> > OVRPRTF    FILE(PICKLGL) DEVTYPE(*AFPDS) PAGESIZE(8.5 +
> >             14 *UOM) LPI(8) CPI(16.7) FRONTMGN(.7 +
> >             1.0) PAGRTT(90) FRONTOVL(AXSLIB/PICKLGL5) +
> >             OUTQ(RMTIBM) SAVE(*YES)
> > which resulted in the report NOT printing, and the error messages
> >
> > AFP data stream in user space  not valid.
> > Error occurred while transforming data.
> > Send request failed for spooled file PICKLGL.
> >
> > Obviously the culprit is the overlay. The question
> > What in the overlay is causing this problem, and how can it be rectified?
> >
> > Again, if anyone has any ideas, help or guidance, it is always MUCH
> > appreciated
> >
> >
> >
> > Alan Shore
> > Programmer/Analyst, Direct Response
> > E:AShore@xxxxxxxx
> > P:(631) 200-5019
> > C:(631) 880-8640
> > "If you're going through Hell, keep going" - Winston Churchill
> > __________________
> >
> > Hi guys
> > I'm having a problem with attempting to print to legal size paper in
> > landscape mode
> > The result is that instead of printing the full 14 inches width, I can
> only
> > print up to 11 inches wide no matter what I do with CPI etc on the
> ovrprtf
> > command
> > Investigating the problem shows that I get the error message CPF6DF2
> > which translates to
> > AFP data stream in user space  not valid.
> >
> > Now I've googled CPF6DF2, and the answers I obtain don't help me to
> > determine the cause of this problem.
> >
> > I was wondering if anyone else had encountered this message id and how
> they
> > rectified it
> >
> > As always, any help and/.or guidance is MUCH appreciated
> >
> >
> >
> > Alan Shore
> > Programmer/Analyst, Direct Response
> > E:AShore@xxxxxxxx
> > P:(631) 200-5019
> > C:(631) 880-8640
> > "If you're going through Hell, keep going" - Winston Churchill
> > --
> > This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
> list
> > To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> > To subscribe, unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> > or email: MIDRANGE-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives
> > at http://archive.midrange.com/midrange-l.
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
>
>
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.