Re: default outq if outq not exist - CPD3322

[J Franz <franz400@xxxxxxx>]

No - it is not sysval QPRTDEV (well, not exactly..). 
The InfoCenter has a page on
http://publib.boulder.ibm.com/infocenter/iseries/v7r1m0/index.jsp?topic=%2Frzalu%2Frzalurouting.htm


which has this text: 
The system value Default printer (QPRTDEV). If the printer identified in the 
system value does not exist, the output goes to the QPRINT output queue.
 
On this particular system (which I cannot freely change), the QPRTDEV = PRT08 
and an outq exists, BUT NO DEVICE of same name...
but it is only when an override printer file is to a non-existent queue (not 
device..) and the RPGLE executes & writes to the spool, that the CPD3322 appears 
in the log to indicate spool was placed in QPRINT (and my original problem was 
that it went to the QGPL/QPRINT and not the QUSRSYS/QPRINT higher in libl (spent 
a while looking in wrong outq..)

Have coded a solution which works with the forms tool (checking existence of 
queue name and if not found, referencing qgpl/qprint). I would need own system 
to determine exactly when this does or does not occur in various scenarios. 

Jim Franz


________________________________
From: sjl <sjl_abc@xxxxxxxxxxx>
To: midrange-l@xxxxxxxxxxxx
Sent: Wed, September 26, 2012 4:23:51 PM
Subject: Re: default outq if outq not exist - CPD3322

Hmmmmm....

DSPSYSVAL SYSVAL(QPRTDEV)

;-)

-sjl


"Carel Teijgeler"  wrote in message 
news:mailman.3595.1348689842.2683.midrange-l@xxxxxxxxxxxx...

Jim,

the default output queue can be set by some initial value. It is not in the
SYSVAL list, but it is in a maintennace screen, where you could set some
basic values for the operating system.

I am not near a machine, and it is many moons ago I have looked at that
screen.

So, if you change that value that will also be shown in the message.

Regards,
Carel Teijgeler

*********** REPLY SEPARATOR  ***********

On 26-9-2012 at 10:13 J Franz wrote:

> I know that IBM will issue a CPD3322 when a RPG executes and the printer
file
> outq does not exist, and the CPD332 says outq is changed to QPRINT.
>
> It appears on our current system it is always QGPL/QPRINT even though for
whatever reason we have a QUSRSYS/QPRINT higher in library list, plus the
> QGPL/QPRINT lower in libl.
>
> I checked another more basic system and see the QUSRSYS/QPRINT is not
there (and it's a default install).
> We have to pass the spool file outq & lib to a "forms product" and it
won't deal with "*LIBL" (blows up).
> Can anyone confirm that CPD3322 has & always will be QGPL/QPRINT?
>
> Jim Franz
> -- 
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
>
>
>
> -----
> Geen virus gevonden in dit bericht.
> Gecontroleerd door AVG - www.avg.com
> Versie: 10.0.1382 / Virusdatabase: 2441/5291 - datum van uitgifte:
09/25/12