You can use either port, just set the IP address of the PC you're going to use appropriately for the selected port.

If it was me, I would use the OTHER port from the one I'm going to connect to my network so that I could change that port's IP address and verify access to it before I disconnected.

- Larry "DrFranken" Bolhuis

www.frankeni.com
www.iDevCloud.com
www.iInTheCloud.com

On 12/31/2012 10:18 AM, Jeff Crosby wrote:
Thanks, Pete. The information says:

ETH0 (T1) 192.168.2.147
ETH1 (T2) 192.168.3.147

which are the defaults. Does this mean the ethernet cable I use should get
plugged into either the T1 or T2 jack in the I5?





On Sun, Dec 30, 2012 at 9:53 AM, Pete Massiello - ML <
pmassiello-ml@xxxxxxxxxxxx> wrote:

Jeff,

To find out the address of your ASMI port, on the bezel, go to Sequence 30
(will have to be in manual mode first), and the 2 addresses are the HMC1
and HMC2 port respectively.

Pete

--
Pete Massiello
iTech Solutions
http://www.itechsol.com
http://www.iInTheCloud.com




-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx [mailto:
midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jeff Crosby
Sent: Friday, December 28, 2012 3:04 PM
To: Midrange Systems Technical Discussion
Subject: Re: Remote power up of System i 520

Don't laugh at this idea.

2 PCs here can function as LAN Console. Each has 2 NIC cards, with the
2nd NIC dedicated to the LAN Console connection. There is a single Linksys
switch on top of the System i rack with 3 ethernet cables attached:

1) To the T5 (I think) jack on the System i (10.10.10.1)
2) To my PC (10.10.10.2)
3) To the office manager's PC (10.10.10.3)

This is a completely isolated network. If I run an ethernet cable from
the ASMI to that switch and can figure out the IP address of the ASMI, can
I just point a browser from my PC to https://xxx.xxx.xxx.xxx where
xxx.xxx.xxx.xxx is the IP address? And then I could RDP to my desktop from
home and away we go?



On Fri, Dec 28, 2012 at 2:26 PM, Kirk Goins <kirkgoins@xxxxxxxxx> wrote:

I think this will work and says about $10K for an HMC...
Find the default AMSI/HMC port IP addresses for your system Attach a
laptop to which ever HMC port you choose using the same IP subnet as
the port you are attaching to Open a browser session and log in to
AMSI Set the other HMC port to an address that is compatible with your
local network including Gateway address Cable up that port up to the
local network and access AMSI In there I believe you can Power Up the
Managed System.

.



On Fri, Dec 28, 2012 at 11:18 AM, Jeff Crosby
<jlcrosby@xxxxxxxxxxxxxxxx
wrote:
Short of an HMC, is there any way to remotely power up a System i 520?

I have LAN Console and Remote Control Panel on my desktop at work.
Due
to
power issues last week (low voltage from utility) after a power
outage, I changed QPWRRSTIPL to 0 for no power up when power is
restored.
In a future outage that results in my power handling program
shutting
down
the system, I have no recourse to power it up other than 1) drive in
to work, or 2) get an HMC, correct?

I can remote from home to my work desktop, but since the System i is
powered off, there ain't not no Remote Control Panel.

Thanks.

--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

The opinions expressed are my own and not necessarily the opinion of
my company. Unless I say so.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L)
mailing
list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please
take a moment to review the archives at
http://archive.midrange.com/midrange-l.



--
Kirk
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take
a moment to review the archives at
http://archive.midrange.com/midrange-l.



--
Jeff Crosby
VP Information Systems
UniPro FoodService/Dilgard
P.O. Box 13369
Ft. Wayne, IN 46868-3369
260-422-7531
www.dilgardfoods.com

The opinions expressed are my own and not necessarily the opinion of my
company. Unless I say so.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list To post a message email: MIDRANGE-L@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx Before posting, please take a
moment to review the archives at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.





As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:
Replies:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.