Re: PTF install questions

Kinda. If you can i would read up on ASMI, configure an IP address and get
access to it. It's a poor man's HMC in that you can turn on/off, modify
front panel settings, read historic SRCs and the like and it's a godsend
when you are remotely ipl'ing a machine. When you somehow fail to include
the RESTART *YES and the machine goes down and you dont have anyone to push
the white button, ASMI is good indeed.
If not, it shouldn't be problematic, just change the panel now and send the
PWRDWNSYS when you can. I dont feel confortable IPL'ing a machine when i
dont have front panel access.

Best Regards,



On Wed, Aug 28, 2013 at 4:34 PM, John McKee <jmmckee@xxxxxxxxxxxxxx> wrote:

I wondered about that this morning. Debated on whether to do it or not.

From previous messages exchanged with Rob, I was not sure if that would

have made a difference.

I started the IPL from my apartment (long boring story). Got to desk and
terminal session was down. My DEVD had ONLINE (*NO). I have since changed
it to *YES. In theory, now, I could then perform a full IPL remotely and
fix this minor irritant. Am I right?

John


On Wed, Aug 28, 2013 at 2:22 PM, Roberto José Etcheverry Romero <
yggdrasil.raiker@xxxxxxxxx> wrote:

Ah! i know what your problem is...
Front panel, does it perchance read: 01 B N V=F P? it should read 01 B N
V=F T. In the same way you have A side and B side for LIC you have P and

T

(permanent and temporal) sides for the FSP's firmware. You are IPL'ing

from

P which is the same as IPLing from A and expecting ptfs to be loaded.
Next time, do a PWRDWNSYS but take care that it's a *FULL and not a *SYS
one. It'll restart the FSP and load the correct fw.

Best Regards!



On Wed, Aug 28, 2013 at 4:15 PM, John McKee <jmmckee@xxxxxxxxxxxxxx>
wrote:

Finally did.

DSPPTF SELECT(*ACTRQD)
shows eight MH PTFs - 1076, 1073, 1070, 1053, 1007, 1004, 1001, 0997.

All

permantly applied. All show "Permanently applied - IPL". IPL source

is

##MACH#B ##SERV#P.

Displaying general information for 5722999 MH01076 shows Server IPL
required ##SERV#T

Sticking my neck way out - does this imply that a second IPL from "B"

side

will fix?

We had PTFs temp applied on "B" for years. We are IPLed, now, on "B".

Did

IPL this morning only end up syncing B and A sides, and another IPL

will

fix it?

DSPPTF LICPGM(5722SS1) shows most recent (?) cum as TC10292.

I have applied PTFs suggested in (I have three documents don't remember
which one) manuals for v5r4 to v61 maybe v71 (mind is going). Will

look

through the docs a lot more to be sure nothing was missed. Since

things

are working, predictably, is there any point in loading a more recent
CUME? I know you guys with LOADS more experience say link loader is no
longer an issue. But, is there any point to loading a CUME to get to

next

level if upgrade PTFs are permanently applied?

John McKee
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

list

To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.