Re: SNDDST not working after V7 upgrade

[Evan Harris <auctionitis@xxxxxxxxx>]

As 6.1.1 is a valid release for running power 7 whats the problem with
doing the upgrade after the migration ?

You're still doing an unload/reload so your usual objections to upgrading
post migration are null and void.

Plus you get the advantage that the upgrade is on newer hardware and will
almost certainly run quicker.


On Wed, Dec 18, 2013 at 10:30 AM, <rob@xxxxxxxxx> wrote:

> I take it this was one of those, "let's take a system at 6.1, restore it
> to a new system at 7.1" type of upgrades versus "upgrade the old system to
> 7.1 and then restore it to a new system"?
>
> Well, the basic troubleshooting is always a good start.
>
> http://pic.dhe.ibm.com/infocenter/iseries/v7r1m0/topic/rzair/rzairfixemail.htm
>
> Just a shoot from the hip, but did you run
> CHGATR OBJ('/tmp') ATR(*RSTDRNMUNL) VALUE(*NO)
> Very common problem the last several releases.  One special IBM system
> user id is used to create the email and a stub goes into /tmp and is
> handed off to another process.  Then another special IBM system user id is
> used to process that handoff.  Bam!
>
> Rob Berendt
> --
> IBM Certified System Administrator - IBM i 6.1
> Group Dekko
> Dept 1600
> Mail to:  2505 Dekko Drive
>           Garrett, IN 46738
> Ship to:  Dock 108
>           6928N 400E
>           Kendallville, IN 46755
> http://www.dekko.com
>
>
>
>
>
> From:   fbocch2595@xxxxxxx
> To:     midrange-l@xxxxxxxxxxxx
> Date:   12/17/2013 04:12 PM
> Subject:        SNDDST not working after V7 upgrade
> Sent by:        midrange-l-bounces@xxxxxxxxxxxx
>
>
>
>
> Hi Folks, any info regarding SNDDST not working after upgrading to V7 from
> V6 and prior to that we sav21 and rst21 to the new iSeries at V6 then
> upgraded to V7.
>
> So, based on a sav21/rst21 I thought we had everything we needed on the
> new iSeries for SNDDST and I think everything we need is started;
>
> servers active
> cfgtcp copied to new i and same sysname and neta and IP's
> same dire's
>
> Any ideas as to how to figure out why the SNDDST command runs with no
> error but does not send to the email address?
>
> Thanks, Frank
>
>
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
> list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.
>
>
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.