Re: Odd Error when doing Chain in RPGLE

If you were talking about COBOL you might be correct - but RPG does not use the buffers directly - all fields are copied from/to a fixed “home” on each I/I operation. If you think about it that is the only way that it could work since RPG can have the same field in multiple files. That just doesn’t work if the field storage is the buffer.

On Feb 29, 2016, at 8:41 PM, aec <cfuture@xxxxxxxxxxx> wrote:

A missing pointer for a CHAIN means that the program does not yet have the pointer set for the value specified.

"Chain to a keyed file using database fields in the key list."

The phrasing seems to indicate you were using field names from the keyed file itself. If so, I'm guessing there's been no I/O on the file so there's been no pointer to the buffer area initialized.

I doubt the error is in QRNXIE, though, if that's an IBM program or procedure.




On 2/29/16 4:50 PM, Jeff Young wrote:

All,
Receiving the following error in the job log:
Message . . . . : 5200 - CALL
PGM(*LIBL/COUPS1) /* The CALL
command contains parameters */

MCH3601 Escape 40 02/29/16 16:40:35.834316 QRNXIE
QSYS *STMT QRNXIE QSYS *STMT
From module . . . . . . . . :
QRNXMSG
From procedure . . . . . . :
SetRepText
Statement . . . . . . . . . : 45

To module . . . . . . . . . :
QRNXMSG
To procedure . . . . . . . :
SetRepText
Statement . . . . . . . . . : 45

Message . . . . : Pointer not set
for location referenced.
Cause . . . . . : A pointer was
used, either directly or as a basing
pointer, that has not been set to
an address.
CPF9999 Escape 40 02/29/16 16:40:35.834481
QMHUNMSG *N COUPS1 T37REBATE *STMT
To module . . . . . . . . . :
COUPS1
To procedure . . . . . . . :
COUPS1
Statement . . . . . . . . . : 68000

Message . . . . : Function check.
MCH3601 unmonitored by QRNXIE at statement
0000000045, instruction X'0000'.

Cause . . . . . : An escape
exception message was sent to a program which
did not monitor for that message.
The full name of the program to which the
unmonitored message was sent is
QRNXIE QRNXMSG SetRepText. At the time the
message was sent the program was
stopped at higher level language statement
number(s) 0000000045. If more than
one statement number is shown, the
program was a bound program.
Optimization does not allow a single statement
number to be determined. If *N is
shown as a value, it means the actual
value was not available. Recovery .
. . : See the low level messages
previously listed to locate the
cause of the function check. Correct any
errors, and then try the request
again.
RNQ0222 Sender copy 99 02/29/16 16:40:35.840653 QRNXIE
QSYS *STMT QRNXIE QSYS *STMT
From module . . . . . . . . :
QRNXMSG
From procedure . . . . . . : InqMsg

Statement . . . . . . . . . : 15

To module . . . . . . . . . :
QRNXMSG
To procedure . . . . . . . : InqMsg

Statement . . . . . . . . . : 15

Message . . . . : Pointer or
parameter error (C G D F).
Cause . . . . . : RPG procedure
COUPS1 in program T37REBATE/COUPS1 at
*...+....1....+....2....+....3....+....4....+....5....+....6....+....7....+....8....+....9....+....0....+....1....+....2....+....3
statement 068000 had an error due to
a pointer not being correctly set. The
cause of the error is most likely
one of the following: -- A basing pointer
was not set. -- A procedure pointer
was not set. -- The pointer was set, but
the object it referenced has been
destroyed. -- A parameter was not passed
5761SS1 V6R1M0 080215 Job Log
S06B6D65 02/29/16 16:44:17 Page 31
Job name . . . . . . . . . . : ROUTE_INV User . . . . . . :
VAIJY Number . . . . . . . . . . . : 502671
Job description . . . . . . : VAIJOBD Library . . . . . :
QGPL
MSGID TYPE SEV DATE TIME FROM PGM
LIBRARY INST TO PGM LIBRARY INST
to the program containing the
procedure. -- A parameter was not passed to
the procedure by its caller within
the program. -- A pointer offset was
greater than the size of the space
the pointer was pointing to. Recovery .
. . : Check the job log for more
information on the cause of the error and
contact the person responsible for
program maintenance. Possible choices for
replying to message . . . . . . . .
. . . . . . . : D -- Obtain RPG
formatted dump. S -- Obtain system
dump. G -- Continue processing at *GETIN.
C -- Cancel. F -- Obtain full
formatted dump.
System is at V6R1M0
Last PTF TL64197
Yeah, I know it is way old, but there was never a problem like this before.
The program was doing a Chain to a keyed file using database fields in the
key list.

Any ideas?
The error appears to be in QRNXIE.


Jeff Young
Sr. Programmer Analyst

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.

Please contact support@xxxxxxxxxxxx for any subscription related questions.

Jon Paris

www.partner400.com
www.SystemiDeveloper.com