Re: Zebra ZT411

[Jack Kingsley <iseriesflorida@xxxxxxxxx>]

Here is link from IBM on the zebra printers.

https://www.ibm.com/support/pages/information-printers-zebraeltron


On Thu, Mar 17, 2022 at 6:16 AM Gmail <robertotempesti2@xxxxxxxxx> wrote:

> I think that the very first change to your configuration is MFRTYPMDL,
> the IBM ASCII Printers Guide say that QWPDEFAULT is the best choice.
> After that, one of the most frequent error in configuration is the caret
> character "^" (Hex 5E) translation.
> You have to configure  correctly the FORMAT PREFIX on the menu device's
> menu.
> About that I give you a link:
> http://support.zebra.com/cpws/docs/general/as400_co.htm
>
> Good lucky
>
> Il 16/03/2022 22:05, Don Brown via MIDRANGE-L ha scritto:
> > The printer is connected using a remote writer.
> >
> > CRTOUTQ OUTQ(QUSRSYS/zebra) RMTSYS(*INTNETADR) RMTPRTQ(qld_b0002)
> > AUTOSTRWTR(1)
> > CNNTYPE(*IP) DESTTYPE(*OTHER) TRANSFORM(*YES) MFRTYPMDL(*IBM4232)
> > INTNETADR('x.x.x.x') DESTOPT(*NONE) SEPPAGE(*NO)
> >
> >
> > Thanks
> >
> > Don
> >
> >
> >
> >
> >
> > From:   "Javier Sanchez" <javiersanchezbarquero@xxxxxxxxx>
> > To:     "Midrange Systems Technical Discussion"
> > <midrange-l@xxxxxxxxxxxxxxxxxx>
> > Cc:     "Don Brown" <DBrown@xxxxxxxxxx>
> > Date:   17/03/2022 12:32 AM
> > Subject:        Re: Zebra ZT411
> >
> >
> >
> > Can you tell how you are connecting this printer to the IBM i?  Is it a
> > 5250 emulation?
> >
> > Javier.
> >
> > El mar, 15 mar 2022 a las 22:54, Don Brown via MIDRANGE-L (<
> > midrange-l@xxxxxxxxxxxxxxxxxx>) escribió:
> > Zebra printers
> >
> > We have replaced a Zebra ZM4 with a Zebra ZT411
> >
> > The output queue was using host print transform to an IBM4232 which
> worked
> > for the ZM4 but we only get a flashing light on the new printer and the
> > page disappears off the queue.
> >
> > Just enquiring if anyone is using one of these and would share the print
> > queue setup please.
> >
> > Thanks
> >
> > Don
> >
> > --
> > This email has been scanned for computer viruses. Although MSD has taken
> > reasonable precautions to ensure no viruses are present in this email,
> MSD
> > cannot accept responsibility for any loss or damage arising from the use
> > of this email or attachments..
>
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: https://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at https://archive.midrange.com/midrange-l.
>
> Please contact support@xxxxxxxxxxxxxxxxxxxx for any subscription related
> questions.
>
> Help support midrange.com by shopping at amazon.com with our affiliate
> link: https://amazon.midrange.com