Thanks, but we need the messages before CPF3397 - that message has this for recovery -
"Recovery . . . : See the job log of the writer that ended to determine the cause of the writer failure."
CPF3397 only tells you an error happened - we have to go back in time, before that message, to "...determine the cause..."
I'm glad it looks like you still have that job log.
Regards
Vern
On Thu, 7 Mar, 2024 at 2:32 PM, gio.cot via MIDRANGE-L <midrange-l@xxxxxxxxxxxxxxxxxx> wrote:
To: 'midrange systems technical discussion'
Cc: gio.cot@xxxxxxxxxxx
And this the message after CPF3397
Learn more about messages Page 1
5770SS1 V7R4M0 190621 S 1 07/03/24 21:27:29 CET
Message ID . . . . . : CPF1164 Gravity . . . . . . . : 00
Send date . . . . . . : 03/07/24 Sending time. . . . . . : 21:08:26
Message type. . : Completion
From the . . . . . . . . : QSPLJOB CCSID . . . . . . . . : 65535
From work . . . . . . . . . . : PRTES7170W
User . . . . . . . . . . . : QSPLJOB
Number . . . . . . . . . . . : 328503
From the program. . . . . . . . : QWTMCEOJ
Sending now. . . . . . . . . . : 21:08:26,529940
Message . . . : Job 328503/QSPLJOB/PRTES7170W ended 03/07/24
at 9.08.26pm; employees 0.029 seconds; closing code 20
X.
Cause . . . : Job 328503/QSPLJOB/PRTES7170W completed on
07/03/24 at 21:08:26. The processing unit time used is
0.029 seconds. The maximum temporary memory used was 9 megabytes. The
job closing code is 20. The job is finished after 1 steps
routing with secondary closing code 0. Closing codes
of work and its meanings are as follows:
0 - The job completed normally.
10 - Work was completed normally during a shutdown
controlled by the system or subsystem.
20 - The job has exceeded the exit severity (job attribute
ENDSEV).
30 - The job ended abnormally.
40 - Work ended before becoming active.
50 - The job ended while it was active.
60 - The subsystem was terminated abnormally while the job was
active.
70 - The system was closed abnormally while the job was
active.
80 - The job is finished (ENDJOBABN command).
90 - The job was forced to close after the limit expired
of time (ENDJOBABN command).
Correction. . . : For more information, see the collection of
topics related to work management within the category
regarding systems management in the IBM i Information Center,
at
http://www.ibm.com/systems/i/infocenter/.
* * * * * END OF THE LIST * * * * *
Da: gio.cot [mailto:gio.cot@xxxxxxxxxxx<mailto:gio.cot@xxxxxxxxxxx>]
Inviato: giovedì 7 marzo 2024 21:21
A: 'Midrange Systems Technical Discussion' <midrange-l@xxxxxxxxxxxxxxxxxx<mailto:midrange-l@xxxxxxxxxxxxxxxxxx>>
Oggetto: R: Configuration Kyocera MA 3005
Hi Vern
This the job log for printer job with MFRTYPMDL *HPCOLORLJ and SYSDRVPGM
*IBMPJLDRV
5770SS1 V7R4M0 190621 Job registration 07/03/24 21:08:26 CET Page 1
Job Name . . . . . . . . : PRTES7170W User . . . . . . : QSPLJOB Number .
. . . . . . . . . . : 328503
Job Description. . . . . : QSPLPRTW Library . . . . : QGPL
IDMSG GRAV TYPE DATE TIME FROM PGM INST LIBRARY TO PGM INST LIBRARY
CPF1124 Information 00 07/03/24 21:07:45,308425 QWTPIIPP QSYS 04CC *EXT *N
Message . . . : Job
328503/QSPLJOB/PRTES7170W started on 03/07/24 at
21:07:45 in the QSPL subsystem in
QSYS. Work entered into the system on
03/07/24 at 9.07.45pm..
*NONE Request 03/07/24 21:07:45,308738 QWTSCSBJ *N QCMD QSYS 0195
By the user. . . . . . . . : MYUSER
Message . . . : -CALL QSYS/QSPWTRM1
MCH1211 Exit 40 07/03/24 21:08:26,464336 QWPZSCL QSYS *STMT QWPZSCL QSYS
*STMT
From the form. . . . . . . . : QWPZSCL
From the procedure. . . . . . : reduce
Instruction. . . . . . . . . : 6
To the form. . . . . . . . . : QWPZSCL
To the procedure. . . . . . : reduce
Instruction. . . . . . . . . : 6
Message . . . : Attempted to divide by
zero for
the fixed-point operation.
CPF3698 Information 00 07/03/24 21:08:26,466249 QSCPUTR QSYS 005E QSCGSO
QSYS 0054
Message . . . : Dump output was sent
to file 1, job
328503/QSPLJOB/PRTES7170W was
created on system MYSYS on 07/03/24
9.08.26pm.
Cause . . . . . : Dump output is sent
to a spool file.
CPF3698 Information 00 07/03/24 21:08:26,520961 QSCPUTR QSYS 005E QSCGSO
QSYS 0054
Message . . . : Dump output was sent
to file 2, job
328503/QSPLJOB/PRTES7170W was
created on system MYSYS on 07/03/24
9.08.26pm.
Cause . . . . . : Dump output is sent
to a spool file.
C2M1601 Exit 50 07/03/24 21:08:26,525045 QC2UTIL1 QSYS *STMT QWPPJLDR QSYS
*STMT
From the form. . . . . . . . :
QC2SIGNL
From the procedure. . . . . . :raise
Instruction. . . . . . . . . : 6
To the form. . . . . . . . . : WPPJLDR
To the procedure. . . . . . :
Signal_Handler
Instruction. . . . . . . . . : 4
*PRCLT
Message . . . : SIGABRT (abend) signal
issued.
Cause . . . . . : The SIGABRT signal
indicating an end has been issued
anomalous.
CEE9901 Release 30 07/03/24 21:08:26,525207 QLEAWI QSYS *STMT QSPOPNWT QSYS
04BB
From the form. . . . . . . . : QLETOOL
From the procedure. . . . . . : Q LE
AWIRaise
Instruction. . . . . . . . . : 176
Message . . . : Application error. *N
not monitored by *N
to high level education *N,
education X'4000'.
Cause . . . . . : The application
closed abnormally due to a
error that was not handled. The name
of the program to which it is sent
the unhandled error is *N *N . The
program was interrupted, on the spot
in which the message was sent, to
instruction number *N del
high level language. If multiple
instruction numbers are displayed
the program in question is an
optimized ILE program. The optimization
it does not allow you to determine a
single instruction number. If he comes
*N is displayed, it means that the
real value was not available.
Correction. . . : To find the cause
of the problem, examine the
lower level messages listed above.
Correct the
5770SS1 V7R4M0 190621 Job registration MYSYS 07/03/24 21:08:26 CET Page 2
Job Name . . . . . . . . : PRTES7170W User . . . . . . : QSPLJOB Number .
. . . . . . . . . . : 328503
Job Description. . . . . : QSPLPRTW Library . . . . : QGPL
IDMSG GRAV TYPE DATE TIME FROM PGM INST LIBRARY TO PGM INST LIBRARY
errors and, therefore, resubmit the
request.
CPF3473 Exit 60 07/03/24 21:08:26,527800 QSPOPNWX QSYS 023B QCMD QSYS 01C8
Message . . . : The writer program
328503/QSPLJOB/PRTES7170W is not
finished normally.
Correction. . . : See messages listed
above for
Determine the cause of the writer's
error. Correct
any errors and restart the writing
program.
CPC2402 Completion 50 07/03/24 21:08:26,527985 QCMD QSYS 066F *EXT *N
Message . . . : The work is finished.
The command processor has received
the cancellation message.
Cause . . . . . : A severe message has
arrived at the command processor
equal to or greater than the end
severity. Correction. . . : See i
previously listed messages to
determine which message caused it
the end of the work. Correct the
errors and then resubmit
request.
CPC2191 Completion 00 07/03/24 21:08:26,529215 QLIDLOBJ QSYS 0702 QLICLLIB
QSYS 09AF
Message . . . : Object SPLAPISPJL in
type QTEMP was deleted
*USRSPC.
CPC2191 Completion 00 07/03/24 21:08:26,529813 QLIDLOBJ QSYS 0702 QLICLLIB
QSYS 09AF
Message . . . : The PJL_DRVRSP object
in type QTEMP has been deleted
*USRSPC.
CPF1164 Completion 00 07/03/24 21:08:26,529915 QWTMCEOJ QSYS 0161 *EXT *N
Message . . . : Job
328503/QSPLJOB/PRTES7170W ended 03/07/24
at 9.08.26pm; employees 0.029
seconds; closing code 20 .
Cause . . . : Job
328503/QSPLJOB/PRTES7170W completed on
07/03/24 at 21:08:26. The processing
unit time used is
0.029 seconds. The maximum temporary
memory used was 9 megabytes. The
job closing code is 20. The job is
finished after 1 steps
routing with secondary closing code
0. Closing codes
of the work and the related meanings
are as follows: 0 - The work was
completed normally. 10 - The job was
completed properly
normal during a controlled shutdown
of the system or subsystem. 20
- The job has exceeded the exit
severity (ENDSEV job attribute). 30
- The job ended abnormally. 40 - The
work finished before
become active. 50 - The job ended
while it was active. 60 - The
subsystem crashed while the job was
active. 70
- The system crashed while the job
was active. 80
- The job is finished (ENDJOBABN
command). 90 - The closing of the work is
was forced after the time limit
expired (ENDJOBABN command).
Correction. . . : For more
information, see the collection of
topics related to work management
within the category
regarding systems management in the
IBM i Information Center,
at
http://www.ibm.com/systems/i/infocenter/.
Thanks
midrange.com
