Re: Disk imminent failure handling -- PCTECH

As David mentioned, use Ghost or some other app to clone the drive or,
failing that, use decent backup software to avoid a re-install.  Cheap
source for legal software:
http://www.buycheapsoftware.com/symantec_products~subcategory~61.asp You
can buy OEM software and they'll include qualifying hardware.


If you do go down the re-install route, start with W2K Service Pack 4 as
the first update (available at
http://www.microsoft.com/windows2000/downloads/servicepacks/sp4/sp4Eng.m
spx ).  Since it's cumulative, it'll cover a fair number of the early
updates in one shot.  After SP4, I'd say do your apps and drivers for
peripherals and then go back to Windows/Microsoft Update.  Reason being
is if an app adds another component like a different DirectX version,
you'll get all of the updates in fewer passes.  Ditto for driver updates
that MS supplies.

Also, after each Update cycle finishes (download - install - reboot), do
another.  Repeat until no more fixes are available.  Some fixes are
fixes for other (broken) fixes so they won't show up until the broken
fix is installed. 


Ultimately, you don't want to be running off of failing hardware.  It
could go at any time.  Take the inconvenience to replace it now;
otherwise it'll fail when you need the machine.

Also, unless you really need it I'd skip the partitioning design.  One
160GB partition is just fine.

Finally, if you're not using NTFS, consider moving to it.  It's a bit
more resilient and secure.  Here's how:
http://www.microsoft.com/technet/prodtechnol/winxppro/maintain/convertfa
t.mspx

John A. Jones, CISSP
Americas Information Security Officer
Jones Lang LaSalle, Inc.
V: +1-630-455-2787 F: +1-312-601-1782
john.jones@xxxxxxxxxx

-----Original Message-----
From: pctech-bounces@xxxxxxxxxxxx [mailto:pctech-bounces@xxxxxxxxxxxx]
On Behalf Of qsrvbas@xxxxxxxxxxxx
Sent: Monday, December 04, 2006 9:36 PM
To: pctech@xxxxxxxxxxxx
Subject: [PCTECH] Disk imminent failure handling

I've got a PC that reports a "S.M.A.R.T. Bad, backup and replace" 
message at boot-up time. I know that this is a result of predictive
failure analysis and that I need to get the existing drive out of there
and put another in its place, but I'm not sure of exactly how it ought
to be done.

The drive is a Hitachi 160GB Serial ATA and I have a replacement. 
That drive is in fact currently physically installed as SATA2, but I'm
not yet willing to power the PC back up to install the drive logically.
That's because I don't really know what the steps should be anyway.

The original drive was partitioned off as 20GB, 30GB and 70GB partitions
giving three logical drives. All three partitions have been (apparently)
successfully backed up into files in my AS/400's IFS. The PC runs a
fully patched Win2K.

It's possible that the PC will boot and run off of the 'bad' drive for
another few months, or it might fail as soon as I start it back up
again. Once the three backups completed, I wasn't quite so nervous. I
_really_ don't want to run through the whole Win2K install and all of
the downloads/patches, but I suppose it could be done.

Does anybody have any experience to pass on?

Thanks for any advice on procedures.

Tom Liotta
--
This is the PC Technical Discussion for iSeries Users (PcTech) mailing
list To post a message email: PcTech@xxxxxxxxxxxx To subscribe,
unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/pctech
or email: PcTech-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives at
http://archive.midrange.com/pctech.


This email is for the use of the intended recipient(s) only.  If you have 
received this email in error, please notify the sender immediately and then 
delete it.  If you are not the intended recipient, you must not keep, use, 
disclose, copy or distribute this email without the author's prior permission.  
We have taken precautions to minimize the risk of transmitting software 
viruses, but we advise you to carry out your own virus checks on any attachment 
to this message.  We cannot accept liability for any loss or damage caused by 
software viruses.  The information contained in this communication may be 
confidential and may be subject to the attorney-client privilege. If you are 
the intended recipient and you do not wish to receive similar electronic 
messages from us in the future then please respond to the sender to this effect.