Re: newbie prototype question...

[Michael_Schutte@xxxxxxxxxxxx]

My bad...  get rid of the ExtPGM keyword and change the addnums to PROTO.
for both the PR and PI

Michael Schutte
Work 614-492-7419
email  michael_schutte@xxxxxxxxxxxx


                                                                           
             Michael_Schutte@b                                             
             obevans.com                                                   
             Sent by:                                                   To 
             rpg400-l-bounces@         RPG programming on the AS400 /      
             midrange.com              iSeries <rpg400-l@xxxxxxxxxxxx>     
                                                                        cc 
                                                                           
             03/28/2006 01:49                                      Subject 
             PM                        Re: newbie prototype question...    
                                                                           
                                                                           
             Please respond to                                             
              RPG programming                                              
              on the AS400 /                                               
                  iSeries                                                  
             <rpg400-l@midrang                                             
                  e.com>                                                   
                                                                           
                                                                           




I can't figure out what you are trying to do...

If you are trying to call addnums from RPGLE, you just need to ...

/free
   addnums(num1:num2);
/end-free

If you are trying to call PROTO from CL.  Try using CALLPROC


Michael Schutte
Work 614-492-7419
email  michael_schutte@xxxxxxxxxxxx



             "Jake M"
             <jakeroc@xxxxxxxx
             m>                                                         To
             Sent by:                  "RPG programming on the AS400 /
             rpg400-l-bounces+         iSeries" <rpg400-l@xxxxxxxxxxxx>
             michael_schutte=b                                          cc
             obevans.com@midra
             nge.com                                               Subject
                                       newbie prototype question...

             03/28/2006 11:46
             AM


             Please respond to
              RPG programming
              on the AS400 /
                  iSeries
             <rpg400-l@midrang
                  e.com>






I am trying to execute a simple prototype program but I keep getting an
error(it compiles fine). I am calling the program as follows:

CALL PGM(MYLIB/PROTO) PARM(1 2)

There might be a very simple mistake I am doing..I am also looking for a
very simple example on a subroutine program and a program which uses /COPY.
Any help in this matter will be greatly appreciated.

     D addnums         PR                  EXTPGM('PROTO')
     D  num1                          1  0
     D  num2                          1  0

     D addnums         PI
     D  num1                          1  0
     D  num2                          1  0


     D  num3           S              1  0

      /free
         num3 = num1 + num2;
         dsply num3;
         dsply 'DONE';
         *inlr = *on;
      /end-free

Error:

D
Pointer or parameter error (C G D F).

Thanks in advance,

Jake.
--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.



--
This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing list
To post a message email: RPG400-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/rpg400-l
or email: RPG400-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/rpg400-l.