Re: SNDEMAIL command error

["Prevesh Kuni" <KuniP@xxxxxxxxxxxxx>]

sjl,
 
Luckily - you are not one of the targets on the SNDEMAIL list so your
assumptions have no value - I do understand what you are trying to say
about 'bots harvesting e-mail addresses and will take that into
consideration next time.
 
I thought the list was put into place to help any sort of problem no
matter how big or small? I looked at the data several times but for some
reason this junior just didn't pick it up - I will try to be more
thorough next time.
 
Prevesh Kuni
RPG Developer
Smollan Group SA (Pty) Ltd
(011) 640 8154 
kunip@xxxxxxxxxxxxx 


> > > sjl_abc@xxxxxxxxxxx 2007/10/01 06:47 PM >>>
Prevesh -

If I were one of the targets of your SNDEMAIL message, I would be a
little 
upset that you just just exposed my email address to the world via the

RPG400-L mailing list. There are lots of 'bots that harvest email
addresses 
from lists like this.

Just a thought:
I always obscure data like this before I send it to a public forum, but
then 
again if you had obscured the email addresses you might have deleted
the '.' 
at the end of the email address that was causing the problem - and then

again, you might have noticed it _before_ sending the message to the
mailing 
list, thus eliminating the necessity to seek help...

- sjl

----- Original Message ----- 
From: "Prevesh Kuni" < KuniP@xxxxxxxxxxxxx >
To: < rpg400-l@xxxxxxxxxxxx >
Sent: Monday, October 01, 2007 3:30 AM
Subject: SNDEMAIL command error


> Good day folks,
>
> I am using the SNDEMAIL command but getting the following error
> CPF3C17.
> Here is the code that I am using:
>
> CPYTOPCD FROMFILE(CLSLIB/CCCLSFEML) TOFLR(CLSEMAIL)
> TODOC(CCUCMF.txt) REPLACE(*YES)
> SNDEMAIL TYPE(*MSG) SMTPID(glinistere@xxxxxxxxxxxxx 
>
> michael@xxxxxxxxxxxxxxx 
>
> shauvette@xxxxxxxxxxxxxxx 
>
> demare.osmni@xxxxxxxxxxxx 
>
> des.devitt@xxxxxxxxxxxx 
>
> fia.potgieter@xxxxxxxxxxxx 
>
> tanya.kruger@xxxxxxxxxxxx 
>
> bstevens@xxxxxxxxxxxx .
> kunip@xxxxxxxxxxxxx )
>
> FROMSMTPID(opsuser@xxxxxxxxxxxxx )
> SUBJECT('UTD Call Cycle Download')
> ATTACHMENT(*DOC) DOC(CCUCMF.TXT)
> FLR(CLSEMAIL) IMPORTANCE(*HIGH)
>
> I use the exact same code to mail another doc. and that works just
> fine? Am I missing something? Would it be case sensitive on the
> CCUCMF.TXT (should be CCUCMF.txt?) or could it be the '.' in one of
the
> addresses ( tanya.kruger@xxxxxxxxxxxx ) however - these addresses are
in
> the other piece of code that works?
>
> Thanks in advance
>
> Prevesh Kuni
> RPG Developer
> Smollan Group
> (011) 640 8154
> kunip@xxxxxxxxxxxxx 
>
> -- 
> This is the RPG programming on the AS400 / iSeries (RPG400-L) mailing
list
> To post a message email: RPG400-L@xxxxxxxxxxxx 
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/rpg400-l 
> or email: RPG400-L-request@xxxxxxxxxxxx 
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/rpg400-l .