RE: XML-INTO with %HANDLER

[MRiggins@xxxxxxxxxxxx]

ok - thanks



From:   "Tyler, Matt" <matt.tyler@xxxxxxxxxxxxxx>
To:     "RPG programming on the IBM i / System i" <rpg400-l@xxxxxxxxxxxx>
Date:   01/26/2012 03:50 PM
Subject:        RE: XML-INTO with %HANDLER
Sent by:        rpg400-l-bounces@xxxxxxxxxxxx



I realized that the copy book HSPECLE and DSPGMINF4 were in the code

Just replace them with something you have or use this code.

HSPECLE:
     H OPENOPT(*NOINZOFL) OPTION(*NODEBUGIO:*SRCSTMT)
     H  BNDDIR('WFIBNDDIR')
      /IF DEFINED(*CRTBNDRPG)
      /IF NOT DEFINED(HSPECLE_OVERRIDE_ACTGRP)
     H  DFTACTGRP(*NO) ACTGRP(*CALLER)
      /ENDIF
      /ELSE
     H  NOMAIN
      /ENDIF
DSPGMINF4:
     D PGMINF         SDS
     D  ProcStatus       *STATUS
     D  ProcRoutin       *ROUTINE
     D  ProcName         *PROC
     D  ParmCount        *PARMS
     D  PrmCnt           *PARMS
     D  ProgName             334    343
     D  Pgmnam               334    343
     D  JobName              244    253
     D  JobNam               244    253
     D  UserName             254    263
     D  JobUsr               254    263
     D  JobNbr               264    269  0
     D  JobDate              270    275  0
     D  JobDat               270    275  0
     D  ProgDate             276    281  0
     D  PgmDat               276    281  0
     D  ProgTime             282    287  0
     D  PgmTim               282    287  0


Thanks, Matt

-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx] On Behalf Of Tyler, Matt
Sent: Thursday, January 26, 2012 2:45 PM
To: RPG programming on the IBM i / System i
Subject: RE: XML-INTO with %HANDLER

I had to parse a four large Lawson Report Writer XML document (up to
several hundred megs big ).   Its structure was not deep and was
consistence enough but repeated an unknown number of times.  I first
coded the XML-INTO with a handler.   During testing it took about 3
minutes for the documents to be processed.  I ended up going to the
XML-SAX (I forget the exact reason but it was because of the document I
had to process), when I was done figuring out all the needed handler
code the same documents processed in 30 seconds. 

It was more work with the XML-SAX but I learned a lot from the
experience. 

Below are code samples I used to build my experience with the XML-SAX
parser. 

http://code.midrange.com/6ad9d425e7.html
http://code.midrange.com/36f1294cf9.html
http://code.midrange.com/2258cfb028.html


try them out.

Thanks, Matt
-----Original Message-----
From: rpg400-l-bounces@xxxxxxxxxxxx
[mailto:rpg400-l-bounces@xxxxxxxxxxxx] On Behalf Of
MRiggins@xxxxxxxxxxxx
Sent: Thursday, January 26, 2012 2:04 PM
To: RPG programming on the IBM i / System i
Subject: Re: XML-INTO with %HANDLER

Are you using %handler because the PO data structure is too big when you

make the arrays as big as you need? (Just curious.)

        Yes that is correct.

The example I sent just showed one POChange set.  There will be multiple

POChange sets and I wanted to be able to process an XML file that had an

unknown number of these sets.

Thanks, 
MLR



From:   Barbara Morris <bmorris@xxxxxxxxxx>
To:     rpg400-l@xxxxxxxxxxxx
Date:   01/26/2012 02:59 PM
Subject:        Re: XML-INTO with %HANDLER
Sent by:        rpg400-l-bounces@xxxxxxxxxxxx



On 1/26/2012 12:07 PM, MRiggins@xxxxxxxxxxxx wrote:
> that's good info, I'm concerned that I have 3 nodes at the same level
of
> ChangePODetail.
> I have the ChangePODetail, SplitPODetail and NewPODetail - is that
> possible to handle in this way?

No, if you need to handle the ChangePODetail's using %handler, you'd 
have to handle anything at the same level separately.

Are you using %handler because the PO data structure is too big when you

make the arrays as big as you need? (Just curious.)