Re: Zendsvr and using AJP

[Pete Helgren <pete@xxxxxxxxxx>]

Hmmm.  Googling on the jk_module found an IBM MTU for 6.1 that 
specifically says:

"5.7.3 Tomcat

Tomcat servers will no longer be shipped as part of the 5761-DG1 product
in V6R1. Remove the following directive from customer configurations:

LoadModule jk_module /QSYS.LIB/QHTTPSVR.LIB/QZTCJK.SRVPGM

In addition, unless an open source version of Tomcat with the Tomcat
connector is used instead, remove the following directives from customer
configurations:

JkAsfTomcat
JkLogFile
JkLogLevel
JkMount
JkMountCopy
JkWorkersFile

If an open source version of the Tomcat connector is used, the
information above regarding third-party modules applies to the module
that is loaded into the HTTP server.


Now the interesting part is that this is talking about Tomcat but the 
directive and module are used in Apache, not Tomcat so the MTU is a 
little confusing.

So it looks like the AJP connector doesn't work on 6.1  but I'll keep 
digging.

Pete Helgren
Value Added Software, Inc
www.asaap.com
www.opensource4i.com


On 4/15/2011 6:25 AM, Jim Oberholtzer wrote:
> A little bit of further looking, I could not find the object QZTCJK  of
> any type on any of our systems.  Are you sure the module name is right?
>
> Jim Oberholtzer
> Chief Technical Architect
> Agile Technology Architects
>
>
> On 4/15/2011 6:51 AM, Jim Oberholtzer wrote:
> > Pete:
> >
> > The error is logged in the job log of the server:
> >
> >     From module . . . . . . . . :   QZSRSNDM
> >     From procedure  . . . . . . :   sendMessageToJobLog_CCSID
> >     Statement . . . . . . . . . :   27
> >     To module . . . . . . . . . :   MOD_SO
> >     To procedure  . . . . . . . :   load_module
> >     Statement . . . . . . . . . :   58
> >     Message . . . . :   The specified HTTP Server module cannot be added with
> >       LoadModule.
> >     Cause . . . . . :   The HTTP Server module
> >       /QSYS.LIB/QHTTPSVR.LIB/QZTCJK.SRVPGM specified on the LoadModule
> > directive
> >       cannot be added into the server.  The module name may be misspelled or
> >       another error may have occured while attempting to load the module.
> > For
> >       more information, see the previous messages in the job log.
> > Recovery  . . .
> >       :   This message may be a result of attempting to load a module that
> > is not
> >       compatible with the version of the HTTP Server (powered by Apache)
> > currently
> >       running on the system.  The version of the HTTP Server (powered by
> > Apache)
> >       is 20051115 . Contact the provider of the module for service. Technical
> >       description . . . . . . . . :   If you are the developer of the
> > module, look
> >     at member AP_RELEASE in file QHTTPSVR/H on the system the module was
> > built
> >     on.  The AP_RELEASE member contains the version number used by the
> > module.
> >     If the version number does not match the version of the HTTP Server
> > (powered
> >     by Apache), rebuild the module with the appropriate version of the header
> >     file. After performing the appropriate recovery, start the server again.
> >
> > It won't start on V7 either.
> >
> > Jim Oberholtzer
> > Chief Technical Architect
> > Agile Technology Architects
> >
> >
> > On 4/14/2011 7:25 PM, Pete Helgren wrote:
> > > >   I want to frontend Tomcat with my Zend server Apache instance and I
> > > >   can't  seem to get it to work (works like a champ in Windows).  I
> > > >   configured the workers.properties file and the uriworkmap.properties
> > > >   file and added the following directives to httpd.conf.
> > > >
> > > >   LoadModule mod_jk /QSYS.LIB/QHTTPSVR.LIB/QZTCJK.SRVPGM
> > > >
> > > >
> > > >   JkWorkersFile conf/workers.properties
> > > >   JkMountFile conf/uriworkermap.properties
> > > >
> > > >   The Zendsvr Apache instance fails to start and also very unhelpfully
> > > >   doesn't log anything anywhere I can see, so I can't tell what Zendsvr
> > > >   Apache instance is cranky about.  Using the directive listing doesn't
> > > >   show any "JK" directives at all.  Is this not supported on IBM i 6.1?
> > > >   If I only attempt to load the module, it also won't start.
> > > >
> > > >   Anybody using AJP connectors on i?