Re: Not a Domino Issue - An AS/400 Issue -- DOMINO400

Sorry, was looking in the wrong place - the 2740xxxx error:

(2629, 2718, 2726, 2728, 2729, 2740, 2741, 2809, 2810, 2824, 282C, 6532, 
6533, 6534, 671A) Reference Codes
These Storage IOAs are allowed only on migrated towers. See Migrated 
Expansion Unit Problem Analysis, Repair and Parts, SY44-5968-00.

That book is here: 
http://publib.boulder.ibm.com/iseries/v5r1/ic2924/v5r1hwpdf/pdf/y4459680.pdf

9010 Cache data associated with attached devices cannot be found Perform 
?SDIOP-PIP31? on page 450.

SDIOP-PIP31
Note: Determine if the system has logical partitions. Go to ?Determining 
if the
System Has Logical Partitions? on page 875, before continuing with this
procedure.
SDIOP PIPs
450 AS/400 Migrated Expansion Tower Problem Analysis, Repair and Parts 
V4R5
Note: If the system has logical partitions, perform this procedure from 
the logical
partition that reported the problem.
Introduction: Cache data associated with the attached devices cannot be 
found.
You were sent to this procedure from URC 9010.
1. Did you just exchange the storage I/O adapter as a result of a failure?
Yes No
? Go to step 6 of this procedure.
2. Reclaim the cache storage (see ?Reclaim IOP Cache Storage? on page 
892).
Note: The system operator may want to restore data from the most recent
saved tape after you complete the repair.
3. Does the IPL complete succesfully?
Yes No
? Go to ?Starting Point For All Problems? on page 3 to correct the
problem.
This ends the procedure.
4. Before completing this service action, perform the following:
a. Power off the system (see ?Powering On and Powering Off the System or
Expansion Tower? on page 868).
b. Replace the cache directory card from the failed storage I/O adapter 
with
the cache directory card that came with the replacement storage I/O
adapter (see ?Cache Directory Card, For Type 2740, 2748? on page 624).
c. Select the IPL type and mode that are used by the customer (see AS/400
Service Functions).
d. Power on the system.
5. Does the IPL complete successfully?
No Yes
? This ends the procedure.
6. Have the I/O cards been moved or reconfigured recently?
Yes No
? Go to step 9 of this procedure.
7. Perform the following:
a. Power off the system (see ?Powering On and Powering Off the System or
Expansion Tower? on page 868).
b. Restore all I/O cards to their original position.
c. Select the IPL type and mode that are used by the customer (see AS/400
Service Functions).
d. Power on the system.
8. Does the IPL complete successfully?
No Yes
? This ends the procedure.
9. Has the system been powered off for several days?
Yes No
SDIOP PIPs
Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and 
Symbolic FRU Isolation 451
? Ask your next level of support for assistance.
This ends the procedure.
10. The cache battery pack may be depleted. Do NOT replace the I/O adapter 
or
the cache battery pack.
Reclaim the cache storage (see ?Reclaim IOP Cache Storage? on page 892).
Note: The system operator may want to restore data from the most recent
saved tape after you complete the repair.
11. Does the IPL complete succesfully?
No Yes
? This ends the procedure.
12. Ask your next level of support for assistance.
This ends the procedure.

Chris Whisonant
Comporium
Senior Mid-Range Systems Administrator
IBM eServer Certified Systems Expert - iSeries Technical Solutions V5R2
IBM Certified System Administrator - Lotus Notes and Domino 6/6.5
IBM Certified Associate Developer - Lotus Notes and Domino 6/6.5
803.326.7270

domino400-bounces+chris.whisonant=comporium.com@xxxxxxxxxxxx wrote on 
08/25/2006 01:24:44 PM:


Sorry to bother you with this, as it has nothing to do with Domino.

We have a 170 that is showing 27409010 in the contol panel of the AS/400
and the amber light is on. Also, we can't get a terminal to connect to

it.

Of course, we don't have hardware/software support.

Do you have any ideas as to what we should do or a place to point me to

to

troubleshoot these issues?

Thanks.

 Gregg

_______________________________________________
This is the Lotus Domino on the iSeries / AS400 (Domino400) mailing list
To post a message email: Domino400@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/domino400
or email: Domino400-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/domino400.



NOTICE: This message contains information which may be confidential. If 
the reader is neither the intended recipient nor a person responsible for 
delivering the message to the intended recipient, you are notified that 
any distribution, copying or retention of this communication is strictly 
prohibited. If you have received this communication in error, please 
notify us immediately by return e-mail, telephone or facsimile. Thank you.