RE: Problems with SNADS & V4R5

[Bill Brosch <bbrosch@xxxxxxxxxxx>]

Patrick,

Started & stopped several times.  Already had looked @ the low level
messages on the initiating session, there were none.  Had checked the
jobs in QSNADS (& QSYSWRK too).  Had put the dist queue on hold early on
in the "what the heck is going on" phase of trying to figure what had
happened.

Turned out that the STRMSF (when did that start as a requirement?) needs
to be run (Thanks Neil & Brent!).

Thanks,  Bill.

-----Original Message-----
From: Patrick Townsend [mailto:patownsend@patownsend.com]
Sent: Wednesday, December 27, 2000 4:43 PM
To: MIDRANGE-L@midrange.com
Subject: Re: Problems with SNADS & V4R5


Bill,

I assume that the QSNADS subsystem is started, yes? (just had to ask the
obvious). Try doing the SNDNETF command from a terminal session and then
looking at the lower level messages. There are sometimes informational
messages that can be helpful. Next try looking at each of the jobs in
the
QSNADS subsystem. View their job logs and see if there are any errors
being
reported. Also, have you tried putting a hold on the distribution queue
before using SNDNETF just to see if anything shows up in the queue?

Patrick
---
IBM AS/400 communications, FTP automation, and eCommerce
software and consulting services.

http://www.patownsend.com

----- Original Message -----
From: "Bill Brosch" <bbrosch@stecnet.com>
To: <MIDRANGE-L@midrange.com>
Sent: Wednesday, December 27, 2000 1:17 PM
Subject: Problems with SNADS & V4R5


> Hi all,
>
> Just upgraded to V4R5 over the weekend from V4R4.  Only one problem:
> SNADS has stopped working.
>
> I do a SNDNETF, the command completes okay (no joblog entry), nut
> nothing appears in the DSTQ.  The DSPDSTLOG shows the "*ORG    *NRM"
> entry only.  There are no errors on the DSPDSTLOG, the DSPLOG, or
> QSYSOPR.  System disk is under the warning threshold.
>
> Any ideas?
>
> Bill Brosch
> Swift Technologies
>
> e-mail: bbrosch@swiftorder.com
> web site: http://www.swiftorder.com
> phone: 1-847-289-8339
> fax: 1-847-289-8939
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
david@midrange.com
> +---
>

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to
MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator:
david@midrange.com
+---
+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---