Re: Problems with SNADS & V4R5

["Patrick Townsend" <patownsend@xxxxxxxxxxxxxx>]

Ah, right! There's a dependency between SNADS and MSF when you are sending
email with SNDDST or the QtmmSendMail API. I didn't realize there was a
dependency just for sending files with SNDNETF!

Patrick
---
IBM AS/400 communications, FTP automation, and eCommerce
software and consulting services.

http://www.patownsend.com

----- Original Message -----
From: "Bill Brosch" <bbrosch@stecnet.com>
To: <MIDRANGE-L@midrange.com>
Sent: Thursday, December 28, 2000 5:05 AM
Subject: RE: Problems with SNADS & V4R5


> Patrick,
>
> Started & stopped several times.  Already had looked @ the low level
> messages on the initiating session, there were none.  Had checked the
> jobs in QSNADS (& QSYSWRK too).  Had put the dist queue on hold early on
> in the "what the heck is going on" phase of trying to figure what had
> happened.
>
> Turned out that the STRMSF (when did that start as a requirement?) needs
> to be run (Thanks Neil & Brent!).
>
> Thanks,  Bill.
>
> -----Original Message-----
> From: Patrick Townsend [mailto:patownsend@patownsend.com]
> Sent: Wednesday, December 27, 2000 4:43 PM
> To: MIDRANGE-L@midrange.com
> Subject: Re: Problems with SNADS & V4R5
>
>
> Bill,
>
> I assume that the QSNADS subsystem is started, yes? (just had to ask the
> obvious). Try doing the SNDNETF command from a terminal session and then
> looking at the lower level messages. There are sometimes informational
> messages that can be helpful. Next try looking at each of the jobs in
> the
> QSNADS subsystem. View their job logs and see if there are any errors
> being
> reported. Also, have you tried putting a hold on the distribution queue
> before using SNDNETF just to see if anything shows up in the queue?
>
> Patrick
> ---
> IBM AS/400 communications, FTP automation, and eCommerce
> software and consulting services.
>
> http://www.patownsend.com
>
> ----- Original Message -----
> From: "Bill Brosch" <bbrosch@stecnet.com>
> To: <MIDRANGE-L@midrange.com>
> Sent: Wednesday, December 27, 2000 1:17 PM
> Subject: Problems with SNADS & V4R5
>
>
> > Hi all,
> >
> > Just upgraded to V4R5 over the weekend from V4R4.  Only one problem:
> > SNADS has stopped working.
> >
> > I do a SNDNETF, the command completes okay (no joblog entry), nut
> > nothing appears in the DSTQ.  The DSPDSTLOG shows the "*ORG    *NRM"
> > entry only.  There are no errors on the DSPDSTLOG, the DSPLOG, or
> > QSYSOPR.  System disk is under the warning threshold.
> >
> > Any ideas?
> >
> > Bill Brosch
> > Swift Technologies
> >
> > e-mail: bbrosch@swiftorder.com
> > web site: http://www.swiftorder.com
> > phone: 1-847-289-8339
> > fax: 1-847-289-8939
> >
> > +---
> > | This is the Midrange System Mailing List!
> > | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> > | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> > | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> > | Questions should be directed to the list owner/operator:
> david@midrange.com
> > +---
> >
>
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
> MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
> david@midrange.com
> +---
> +---
> | This is the Midrange System Mailing List!
> | To submit a new message, send your mail to MIDRANGE-L@midrange.com.
> | To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
> | To unsubscribe from this list send email to
MIDRANGE-L-UNSUB@midrange.com.
> | Questions should be directed to the list owner/operator:
david@midrange.com
> +---
>

+---
| This is the Midrange System Mailing List!
| To submit a new message, send your mail to MIDRANGE-L@midrange.com.
| To subscribe to this list send email to MIDRANGE-L-SUB@midrange.com.
| To unsubscribe from this list send email to MIDRANGE-L-UNSUB@midrange.com.
| Questions should be directed to the list owner/operator: david@midrange.com
+---