Re: ip printer problem

["Ron Lang" <rlang@xxxxxxxxx>]

Steve,

I don't know if this is the answer, but I'll take a shot.  Recently we have
switched some printers from IBM infoprint 21's to IBM infoprint 1130's and
had a similar problem.  It turned out that the TCP port number has to be
different,  the 21's use 5001, but the 1130's had to use 9100.

Good Luck,
Ron

----- Original Message -----
From: "Steve Richter" <srichter@AutoCoder.com>
To: <MIDRANGE-L@midrange.com>
Sent: Wednesday, December 05, 2001 9:50 AM
Subject: ip printer problem


> I have configured an *IP attached printer on our as400. When attempting to
> print to it, I get the following error in the PDJ job of the writer:
>
>  Message ID . . . . . . :   PQT3625       Severity . . . . . . . :   40
>  Message type . . . . . :   Diagnostic
>  Date sent  . . . . . . :   12/05/01      Time sent  . . . . . . :
> 09:27:26
>  Message . . . . :   Connection with device ROCHP10 is being retried.
>  Cause . . . . . :   A session cannot be established with the device at
>    RMTLOCNAME 172.24.107.103, using PORT 5001.  The error code is 22.
This
>    indicates one of the following conditions:
>      22:      The device did not respond to a connection request.
>
> The printer is an  HP Laser jet 1100.
>
> We are using an HP Jet Direct 170X to ethernet attach the printer to our
> intranet.
>
> The printer is in  New York, the AS400 is in NJ, all ethernet; frame relay
> and cisco routers connect the two sites.
>
> IP wise, the printer works.  I can print to it from an NT server in
Canada.
>
> The AS400 sees the printer.  I can ping it from the as400.
>
> To config the printer I ran the following cmds:
>      - CrtPsfCfg  PsfCfg( GplAmari/RochP10 )
>                   IpdsPasThr( *Yes )
>                   ActRlsTmr( *NoRdyf )
>                   RlsTmr( *Sec15 )
>      - CrtDevPrt  Devd( RochP10 )
>                   DevCls( *Lan )
>                   Type( *Ipds )
>                   Model( 0 )
>                   LanAttach( *Ip )
>                   Afp( *Yes )
>                   Port( 5001 )
>                   Font( 11 )
>                   FormFeed( *AutoCut )
>                   ActTmr( *NoMax )
>                   RmtLocName( 172.24.107.103 )
>                   UsrDfnObj( GplAmari/ROCHP10 *PsfCfg )
>
> ( These were the config cmds run when I successfully *IP attached a
Lexmark
> laser printer using an IO corp printer server device ).
>
> The ROCHP10 devices varies on, the writer starts and attaches to the *DEVD
> without error.
>
> Any idea why the error code 22: The device did not respond to a connection
> request ?
>
> Thank you,
>
> Steve Richter
>
>
>
> _______________________________________________
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
list
> To post a message email: MIDRANGE-L@midrange.com
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/cgi-bin/listinfo/midrange-l
> or email: MIDRANGE-L-request@midrange.com
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.