Re: How long to initialize disk?

[rob@xxxxxxxxx]

Rough estimate to initialize our disk
Low end:  112 minutes or 1.9 hours
High end:  510 minutes or 8.5 hours

Rob Berendt

==================
"They that can give up essential liberty to obtain a little temporary
safety deserve neither liberty nor safety."
Benjamin Franklin
----- Forwarded by Rob Berendt/DEKKO on 12/07/2001 01:01 PM -----

                    "Larry
                    Youngren"            To:     rob@dekko.com
                    <youngren@us.i       cc:
                    bm.com>              Fax to:
                                         Subject:     Re: How long to 
initialize disk?
                    12/07/2001
                    12:45 PM







Hope this helps.


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  IBMUSM07(youngren)
  Dept. 47U/ 030-2/ Rochester, MN
  Ph 507-253-3600  TieLine 8-553-3600
  VM: RCHVMX2(Youngren)
  Lotus Notes: Larry Youngren/Rochester/IBM
  Internet: youngren@us.ibm.com
---------------------- Forwarded by Larry Youngren/Rochester/IBM on
12/07/2001 11:30 AM ---------------------------




From: Glen Nelson on 12/07/2001 11:19 AM


To:   Larry Youngren/Rochester/IBM@IBMUS
cc:   Tom Crowley/Rochester/IBM

From: Glen Nelson/Rochester/IBM@IBMUS
Subject:  Re: How long to initialize disk?
Importance:    Normal


The general rule of thumb is take the largest drive size (in this case 8G
or 17G) and  use the range of 7 minutes to 15 minutes per G.   Since only
64 units are processed at one time  take the number of units / 64 ( add 1
if there is a remainder) and multiply.   These number are estimates only.
Adds can be done during normal operations so this does not have to be down
time.

So in this example of 75 units

(8*7)*2     -    (8*15)*2
 112          -      240

(17*7)*2  -   (17*15)*2
238          -    510

Glen W. Nelson
507-253-4306
IBMUSM07(glennel)



                    Larry Youngren

                                         To:     Glen
Nelson/Rochester/IBM@IBMUS
                    12/07/2001           cc:

                    07:40 AM             From:   Larry
Youngren/Rochester/IBM@ibmus
                                         Subject:     How long to
initialize disk?







Do you want to take a crack at this ?

(or pass it along to someone ?)


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  IBMUSM07(youngren)
  Dept. 47U/ 030-2/ Rochester, MN
  Ph 507-253-3600  TieLine 8-553-3600
  VM: RCHVMX2(Youngren)
  Lotus Notes: Larry Youngren/Rochester/IBM
  Internet: youngren@us.ibm.com
---------------------- Forwarded by Larry Youngren/Rochester/IBM on
12/07/2001 07:40 AM ---------------------------


rob@dekko.com on 12/07/2001 07:32:07 AM

To:   Larry Youngren/Rochester/IBM@IBMUS
cc:

Subject:  How long to initialize disk?




Mr. Youngren,

I was referred to you by a contact on a 400 web site.

We are moving several drives from one iSeries to our new 840-2418-1542.
Any estimates on how long it will take to
initialize the following:

qty  model
30   6717
45   6718


Robert Berendt, CCP
Group Dekko Services, LLC
Dept 01.073
PO Box 2000
Dock 108
6928N 400E
Kendallville, IN 46755
(219) 347-3100 ext 70560
Fax (219) 349-2005
rob@dekko.com
http://www.dekko.com