Pete,
Cursor on upper left, no connection at all.
Cursor on upper right, DSP01 is not assigned to a specific sub-system.

Have a great day.

Ed Murphy
Silverlake Support  
Jack Henry & Associates
  

-----Original Message-----
From: midrange-l-bounces@xxxxxxxxxxxx
[mailto:midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Pete Helgren
Sent: Saturday, April 01, 2006 11:37 AM
To: Midrange Systems Technical Discussion
Subject: Re: Twinax console refuses to give signon screen

This is really weird.

The devices that I have substituted in are consoles from other systems (

I have an 800 and an 720).  So the addresses are set at 0.  All three 
consoles work on the 800 and the 720.  I even swapped and tested all 
three cables which work on the 800 and 720.  However, when I connect 
them to the 170 I get nothing.  It will autoconfig a 3476 device and the

status goes to vary on pending but the device itself never becomes 
active.  I tried deleting the device several times and I tried other 
addresses just to see if it is a "console" thing.  I varied the 
controller off, deleted the device and then varied the controller on.  I

get a device description created, no signon screen.

The alternate brick was an attempt to isolate a possible hardware issue 
but that brick works on the 720 and is identical to the original on the 
170 but made no difference.  I am down to a possible card problem but 
the 170 isn't reporting any hardware problems at all.

Strange, very strange.

Pete

Jim Franz wrote:

>I know you must have each of the 3 devices you tried at port 0, addr 0
>and you really did cable to port 0 of the 1st twinax controller on the
170?
>Have you (once connected) powered of device then on?
>Then, if not working, is device "type" same on each test device? Is
possible
>the subsystem has workstn entry for diff dev type?
>Go cmdhdw does show the twinax adapter resource is up & ready?
>Can it be varied off/on?
><grasping for straws>
>jim franz
>
>
>----- Original Message ----- 
>From: "Pete Helgren" <Pete@xxxxxxxxxx>
>To: "Midrange Mailing List" <MIDRANGE-L@xxxxxxxxxxxx>
>Sent: Friday, March 31, 2006 10:50 PM
>Subject: Twinax console refuses to give signon screen
>
>
>  
>
>>I am stumped with this one.  I have a 170 that I usually have a
console
>>connected to but the thing is bulky and takes up space so I unplugged
it
>>and put it away.  Now that I need it, I can't get the thing to give me
a
>>signon screen.  I tried 3 different terminals.  Three different twinax
>>cables and even a different 4 port "brick" I borrowed from another
>>machine.  No joy.  I can delete  DSP01 and it will autoconfig another
>>one (at address 0 port 0 on the correct controller)  but the cursor
just
>>hangs on the right hand side of the screen.  No signon.
>>
>>I *think* I have ruled out a hardware problem.  There are no messages.
>>No SRC's. Nuthin'. It has to be a configuration issue but I sure can't
>>think of anything I might have missed.
>>
>>Any ideas?
>>
>>Thanks,
>>
>>Pete Helgren
>>-- 
>>This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing

>>list
>>To post a message email: MIDRANGE-L@xxxxxxxxxxxx
>>To subscribe, unsubscribe, or change list options,
>>visit: http://lists.midrange.com/mailman/listinfo/midrange-l
>>or email: MIDRANGE-L-request@xxxxxxxxxxxx
>>Before posting, please take a moment to review the archives
>>at http://archive.midrange.com/midrange-l.
>>
>>    
>>
>
>
>  
>

As an Amazon Associate we earn from qualifying purchases.

This thread ...

Follow-Ups:

Follow On AppleNews
Return to Archive home page | Return to MIDRANGE.COM home page

This mailing list archive is Copyright 1997-2024 by midrange.com and David Gibbs as a compilation work. Use of the archive is restricted to research of a business or technical nature. Any other uses are prohibited. Full details are available on our policy page. If you have questions about this, please contact [javascript protected email address].

Operating expenses for this site are earned using the Amazon Associate program and Google Adsense.