Re: HMC session hung

[ankush agrawal <aankush39@xxxxxxxxx>]

Yes, from HMC itself

On Tue, Aug 9, 2011 at 5:47 PM, Jack Kingsley <iseriesflorida@xxxxxxxxx>wrote:

> Did you start the shared key from the hmc itself.
>
> On Tue, Aug 9, 2011 at 12:39 AM, ankush agrawal <aankush39@xxxxxxxxx>
> wrote:
>
> > Hi All,
> >
> > Yesterday, I faced a strange issue. I was loading cum packages on system.
> > System was in restricted state and i was accessing it through HMC. After
> > loading packages, Go PTF option 8, my HMC session hung. I waited for
> about
> > half an hour but it didn't come back. Then I disconnected the session and
> > login to another HMC session. As I gave the session key, it threw below
> msg
> > at the bottom of screen.
> >
> > 043 ; Connected, waiting for partition screen. But it didnt connect.
> >
> > Then, after an hour one of my colleague, logged in to HMC session and he
> > disconnected my session and was able to connect. I checked the history
> logs
> > and found below error messages:
> >
> > PTFs installed successfully.
> > Local system sent SNA negative response data to controller CTL01 on
> device
> > D
> > Local system sent SNA negative response data to controller CTL01 on
> device
> > D
> > Local system sent SNA negative response data to controller CTL01 on
> device
> > D
> > Device DSP01 no longer communicating.
> > Session stopped by a request from device DSP01.
> > Device DSP01 no longer communicating.
> > Device DSP01 no longer communicating.
> > Device DSP01 no longer communicating.
> >
> >
> > Message ID . . . . . .
> > :   CPI5906
> > Date sent  . . . . . . :   08/06/11      Time sent  . . . . . . :
> > 03:03:13
> >
> >
> > Message . . . . :   Local system sent SNA negative response data to
> > controller
> >  CTL01 on device
> > DSP01.
> >
> >
> > Cause . . . . . :   The remote system may have sent Systems
> > Network
> >  Architecture (SNA) data that does not conform to SNA protocols or
> > the
> >  configuration is not
> > correct.
> > Recovery  . . . :   If the controller is a host system, this may not be
> > an
> >
> > error.
> >    If the controller is a host-type controller, the remote system may
> > have
> >  more logical units varied on than there are device descriptions
> > configured
> >  or varied on and attached to the controller at the local
> > system.
> >    If the controller is an advanced program-to-program communications
> > (APPC)
> >  controller or host-type controller, verify the following device
> > description
> >
> >
> > Can anyone help me in understanding about the issue.
> >
> >
> >
> >
> > Thanks,
> >
> > Ankush
> > --
> > This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing
> list
> > To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> > To subscribe, unsubscribe, or change list options,
> > visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> > or email: MIDRANGE-L-request@xxxxxxxxxxxx
> > Before posting, please take a moment to review the archives
> > at http://archive.midrange.com/midrange-l.
> --
> This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
> To post a message email: MIDRANGE-L@xxxxxxxxxxxx
> To subscribe, unsubscribe, or change list options,
> visit: http://lists.midrange.com/mailman/listinfo/midrange-l
> or email: MIDRANGE-L-request@xxxxxxxxxxxx
> Before posting, please take a moment to review the archives
> at http://archive.midrange.com/midrange-l.