Re: Migrate twinax console to LAN console V5R2

believe your going to set it to lan console via the 65+21 route. Once that
is done then get into sst and set the lan console settings. once you set
the lan console settings then you can est the lan console software on the
pc side.

On Mon, Jul 2, 2012 at 3:09 PM, Lindstrom, Scott R. <
Scott.Lindstrom@xxxxxxxxxxxxxx> wrote:

Sorry - it says 127.0.0.1.

Scott

________________________________________
From: midrange-l-bounces@xxxxxxxxxxxx [midrange-l-bounces@xxxxxxxxxxxx]
on behalf of Lindstrom, Scott R.
Sent: Monday, July 02, 2012 2:08 PM
To: Midrange Systems Technical Discussion
Subject: RE: Migrate twinax console to LAN console V5R2

Jim - I am in a function 21 now. I got into DST and changed to LAN
console. But so far when I config a session on the PC I get:

The Local configured console name 127.0.0.0 does not match the actual
configured console name <mypcnname>.

Not sure why it's saying that. I have assigned the IP address ending in
.60 to the AS/400, the one ending in .61 to the PC, and am trying to assign
the one ending in .62 to the AS/400 console card in slot C05.

scott

________________________________________
From: midrange-l-bounces@xxxxxxxxxxxx [midrange-l-bounces@xxxxxxxxxxxx]
on behalf of Jim Oberholtzer [midrangel@xxxxxxxxxxxxxxxxx]
Sent: Monday, July 02, 2012 1:14 PM
To: Midrange Systems Technical Discussion
Subject: Re: Migrate twinax console to LAN console V5R2

The procedure in the V5R4 Info center is essentially the same as it was
in V5R2, difference being some of the options for setting up the console
device and the user. You may have to hunt/peck for those. Also, I
don't remember exactly but there was a change where you could get to
those functions with SST, at V5R2 they may only be available from DST.
I would try a function 21 to see if the DST presented that way will give
you the options, otherwise you may have to IPL into DST to set it up.

Jim Oberholtzer
Chief Technical Architect
Agile Technology Architects


On 7/2/2012 12:56 PM, Lindstrom, Scott R. wrote:

Unfortunately that link is for:

Software version:
5.4.5, 6.1, 6.1.1,
V5R4M0, V5R4M5, V6R1M0, V6R1M1

I am V5R2.

________________________________________
From:midrange-l-bounces@xxxxxxxxxxxx [midrange-l-bounces@xxxxxxxxxxxx]

on behalf of Jim Oberholtzer [midrangel@xxxxxxxxxxxxxxxxx]

Sent: Monday, July 02, 2012 11:36 AM
To: Midrange Systems Technical Discussion
Subject: Re: Migrate twinax console to LAN console V5R2

That option was not added until V5R4 I think. You need to use the front
panel (65+21) to change the console. I think the link sent earlier has
the exact instructions.

Jim Oberholtzer
Chief Technical Architect
Agile Technology Architects


On 7/2/2012 11:28 AM, Lindstrom, Scott R. wrote:

Jack - this is opt 8 in V5R2:

8. Work with service tools user IDs

Which brings me here:

Work with Service Tools User IDs
System:
pe option, press Enter.
1=Create 2=Change password 3=Delete
4=Display 5=Enable 6=Disable
7=Change privileges 8=Change description

There is no option to set the console type. Is it somewhere else in

V5R2?

Scott


-----Original Message-----
From:midrange-l-bounces@xxxxxxxxxxxx [mailto:

midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Jack Kingsley

Sent: Monday, July 02, 2012 11:25 AM
To: Midrange Systems Technical Discussion
Subject: Re: Migrate twinax console to LAN console V5R2

start SST, take opiton 8 (Work with service tools user IDs and

Devices),

can you do anything with option 3 that would allow you to change it

to lan

console.



On Mon, Jul 2, 2012 at 12:17 PM, Lindstrom, Scott R.<
Scott.Lindstrom@xxxxxxxxxxxxxx> wrote:

> Sorry - that link was valid before. It is a PDF document

that gives the

> steps to do this V5R4M5 and beyond.
>
> Scott
>
>
> -----Original Message-----
> From:midrange-l-bounces@xxxxxxxxxxxx [mailto:
> midrange-l-bounces@xxxxxxxxxxxx] On Behalf Of Lindstrom,

Scott R.

> Sent: Monday, July 02, 2012 11:16 AM
> To:MIDRANGE-L@xxxxxxxxxxxx
> Subject: Migrate twinax console to LAN console V5R2
>
> I have a V5R2 system that I need to get over to LAN console

so we can add

> some LPAR's. I found this document:
>
>
>

http://www-01.ibm.com/support/docview.wss?uid=nas179a308457dd4c6c18625770e0057530f

>
> But it covers V5R4M5 and beyond; it directs you into SST

option 8 "user

> IDs and*devices*" to set the console type to '3' Ops

Console. In V5R2 the

> 'devices' part is not there.
>
> Does anyone know how I change the console type from Twinax

to Ops LAN

> console in V5R2?
>
> Scott Lindstrom
>
> --

--

--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.
--
This is the Midrange Systems Technical Discussion (MIDRANGE-L) mailing list
To post a message email: MIDRANGE-L@xxxxxxxxxxxx
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/midrange-l
or email: MIDRANGE-L-request@xxxxxxxxxxxx
Before posting, please take a moment to review the archives
at http://archive.midrange.com/midrange-l.